Page 457 - 2018 Racecar Engineering Hot Rod and Early Muscle Car Parts and Accessories Catalog

1982-92 GM F-Body 1982-92 GM F-Body
1998-92 LSX Aluminum Motor Mounts Front Subframe
UMI2323 Repair Kits UMI2662-B
Replace factory steel and rubber motor mounts with Designed to weld-in and provide a
solid lightweight aluminum motor mounts. The sturdy surface and a properly sized hole
6061 aluminum mounts are a direct replace- to restore the frame to a like-new
ment using existing holes. 3 pounds lighter condition. Cutting and welding is
than original. required.

1982-92 LSX Engine Mounts Panhard Bar Lowering Bracket
UMI2406-B UMI2063-B
These mounts allow the installa- For use with factory axle only. May
tion of LS powerplants into 1978-88 ¿W 6WUDQJH UHDU HQGV ZLWKRXW PRGL-
G-Body as well as 1971-92 Camaro/ ¿FDWLRQV /RZHUV D[OH VLGH GULYHU¶V
Firebird applications. The kit includes 3+% PRXQW E\ EROW LQ
adapter plate that allow for the installation for street use. Laser cut and jig built for accuracy. Includes high
of LSX powerplants using factory LS1 motor grade hardware. Supplied powder coated UMI Gloss Black.
mounts. Allows for factory engine location as
well as a rearward relocation up to one inch. Black. Panhard Bar Relocation Conversion Kit
UMI2064-B
Rear Sway Bar UMI2113-R The competition proven setup
The UMI 22mm (7/8") includes a weld-in reinforce-
light weight tubular rear ment plate for the factory
sway bar is designed to panhard bar mount as well as
reduce body roll, under- an adjustable strut to prevent
steer and increase corning capabilities resulting in a more balanced lateral movement of the bracket system. Laser cut adjustment slots
suspension. permit lowering and leveling the panhard bar for roll center height
and performance tuning. This kit gives much of the performance of a
Torque Arm Relocation Kits Watts Link with easier installation and adjustment.
This transmission cross-member with
integrated torque arm mount features the Competition Panhard Bar
correct provisions for mounting the TH350
transmission while still allowing the use of a Lowering/Leveling Kit UMI2062-B
factory style torque arm. The built in torque arm Designed to increase over-the-axle exhaust
mount will work with virtually any stock style pipe clearance and also lower and
aftermarket torque arm as well as the factory level the Panhard bar. The com-
torque arm and features instant center adjust- petition proven setup includes a
ment by moving the front of the torque arm up or down. weld-in reinforcement plate for the
factory panhard bar mount as well as
Part No. Description
an adjustable strut to prevent lateral movement of the bracket system.
UMI2230-B GM F-Body Torque, Black
UMI2230-R GM F-Body Torque, Red Laser cut adjustment slots permit lowering and leveling the PHB for
roll center height and performance tuning. This kit gives much of the
performance of a Watts Link with easier installation and adjustment
1982-02 Camaro Short Antenna
UMI2996 Torque Relocation
Replace factory non-power steel mast antenna with a Replacement Bushing UMI3004
VKRUW EODFN ¿QLVK DQWHQQD This bushing is required when the factory torque
arm is used with the torque arm relocation kit.
1982-92 Boxed Subframe Connectors
The three piece weld-in setup offers unmatched Rear Torque Arm
strength and offers additional clearance Hardware Kit UMI3003
for dual exhaust systems. May
QRW ¿W PRGHOV ZLWK GXDO Kit Includes longer 9/16" Grade 8 bolts to
catalytic converters. accommodate the thicker torque arm mounting
plates. In most cases the factory bolts are too
Part No. Description short. Kit will not work on Moser 12-bolt.
UMI2400-B Black
UMI2400-R Red

456 2018 HOT ROD AND EARLY MUSCLE