The refractive lens is the primary component of beam delivery assemblies. It directs the beam in a desired direction. Protective covers are used to cover the reflector. To prevent contamination, a clean, positive pressure protective gas is added.
Laser Cutting Systems’ unitized cutting machine and LaserMat® II are choice laser cutting machines, offering customers high speed and precision accuracy.
For dual-purpose commercial use, all-in-one laser cutters are available from $42,500 up to $116,000.
Smaller wavelength also contributes to better focus and higher intensity as well. One drawback of these cutters is that their parts wear out because of the high power functionality.
STJ1610M-2 cheap CO2 laser cutter for metal, acrylic, and wood with best budget adopts sealed CO2 glass laser tube, which is used for cutting thin metals (1.5mm SS and 2.5mm CS) and thick nonmetals (30mm acrylic sheet and 25mm wood panel).
Send your design to the laser. In the print driver you’ll select the laser parameters you want to use, or select a preset material setting from GSS Machinery’s extensive database.
Pick the best nozzles for your lens and make sure they are in perfect condition.
With laser cutting, fiber laser (straight), fiber laser plasma combination, and CO2 lasers are typically used. With greater material thicknesses, however, laser cutting makes sense for only special applications, more usually other cutting processes (oxyfuel or plasma cutting) are used here.
We should first verify that all connections (including power supply and exhaust system) have been correctly inserted. Visually inspect the machine's condition. Verify that the machine is free to move and that there are no materials under the table. Make sure that your work area and all optical components are clean. This issue is covered in the "General Maintenance" section. If necessary, check the exhaust system and turn on the cooling system. Make sure that the instructions are followed when installing the filter or activated carbon in the exhaust system. Close the protective cover after you have checked.
Each week, staff must vacuum the equipment with a vacuum cleaner in order to remove any dust or debris.
It is strictly forbidden to turn on the chiller when there is no water or the water level is too low to avoid damage to the water cooling equipment. It is strictly forbidden to squeeze or step on the water inlet and outlet pipes of the chiller to keep the water passages unblocked. The laser beam will cause burns when it irradiates the human skin. Staring into a laser beam for extended periods of time can cause serious damage to the retina of the eye. Operators must wear goggles. The equipment will generate a lot of smoke and dust when cutting certain plates, so the outlet pipe of the fan should be led to the outside, or an air purification device should be installed. In addition, operators should wear dust masks to prevent the occurrence of occupational diseases. When the temperature is below 0 °C for a long time, the cooling water in the water cooler, laser and water pipeline should be drained to prevent the cooling water from freezing when the temperature is too low, causing damage to equipment and pipelines. Check the protective lens inside the cutting head once a day. When the collimating mirror or focusing mirror needs to be disassembled, record the disassembly process. Pay special attention to the installation direction of the lens and do not install it wrong. Turn off the air source and power supply when off work, and the residual air belt in the machine pipeline should be emptied at the same time. If you leave the machine for a long time, please turn off the power to prevent unprofessional operation. Pay attention to observe whether there is lubricating oil on the surface of the horizontal and longitudinal guide rails and the frame of the machine, and maintain good lubrication. If there is an automatic height adjustment device, check whether it is sensitive and whether to replace the probe.
Laser cutting intricate designs in wood, acrylic, paper and other materials is possible with the CO2 laser. Laser cutting layers can be used to create 3D models, invitations, inlays and other items using one laser. The only limit to a laser machine's capabilities is your imagination.
A red light positioning system makes cutting easy to line up, while a cooling system keeps everything safe. There's a handy USB port, and the machine is compatible with CorelDRAW and image formats like JPG, BMP, PNG,CDR, DXF, PLT and TIF. Overall, unless you need to cut metal, you won't find finer.
The work-life of this machine is around 1,00,000 hours. This machine can both, mark and engrave and that too with high precision. The design is plug-and-play and requires almost no consumables. The price range of this industrial fiber laser marking machine varies from 5000 USD to 9000 USD.
Laser Cutting Process Drawbacks
When compared to other techniques, laser cutting requires a high power consumption.
The laser beam is extremely delicate to handle.
If the laser beam comes into contact with human workers, it is hazardous.
Laser cutting is still unable to cut thick metals.
Cutting thick materials is difficult.
The less effective laser cutting becomes as the material thickness increases. For example, when it comes to cutting thick sheets of carbon steel, laser cutting may be difficult.
Laser power of 80W. A laser can typically cut up to 10mm acrylic and up to 9mm soft woods.