Hand and power tools are a common part of our everyday lives and are present in nearly every industry.
Regulations Covering Hand and Power Tools For General Industry 1910 Subpart P, Hand and Portable Power Tools and Other Hand-Held Equipment. What the Regulations Say About Hand Tools Each employer shall be responsible for the safe condition of tools and equipment used by employees, including tools and equipment which may be furnished by employees. What the Regulations Say About Hand Tools Employers shall not issue or permit the use of unsafe hand tools. General Safety Precautions Employees who use hand and power tools and who are exposed to the hazards of falling, flying, abrasive and splashing objects, or exposed to harmful dusts, fumes, mists, vapors, or gases must be provided with the particular personal equipment necessary to protect them from the hazard. General Safety Precautions Appropriate personal protective equipment should be worn due to hazards that may be encountered while using portable power tools and hand tools. Hand Tool Misuse The greatest hazards posed by hand tools result from misuse and improper maintenance.
Hand Tools The employer is responsible for the safe condition of tools and equipment used by employees but the employees have the responsibility for properly using and maintaining tools.
Basic Hand Tool Safety Rules Around flammable substances, sparks produced by iron and steel hand tools can be a dangerous ignition source.
Hazards of Power Tools All hazards involved in the use of power tools can be prevented by following five basic safety rules: Keep all tools in good condition with regular maintenance. General Safety Guidelines for Power Tools Be aware of all power lines and electrical circuits, water pipes, and other mechanical hazards in your work area, particularly those below the work surface, hidden from the operator’s view, that may be contacted.
General Safety Guidelines for Power Tools Power tools can be hazardous when improperly used.
General Safety Guidelines for Power Tools The following general precautions should be observed by power tool users: Never carry a tool by the cord or hose. General Safety Guidelines for Power Tools All observers should be kept at a safe distance away from the work area.
General Safety Precautions- Electric Tools Employees using electric tools must be aware of several dangers; the most serious is the possibility of electrocution.
General Safety Precautions- Electric Tools Under certain conditions, even a small amount of current can result in fibrillation of the heart and eventual death. General Safety Precautions- Electric Tools Electric tools must either have a three-wire cord with ground and be grounded, be double insulated, or be powered by a low-voltage isolation transformer. General Safety Precautions- Electric Tools These general practices should be followed when using electric tools: Electric tools should be operated within their design limitations. Power Tool Accessories and Attachments There’s a variety of accessories available for use on or with power tools.
Powered Abrasive Wheel Tools Powered abrasive grinding, cutting, polishing, and wire buffing wheels create special safety problems because they may throw off flying fragments. Powered Abrasive Wheel Tools To prevent the wheel from cracking, the user should be sure it fits freely on the spindle. Powered Abrasive Wheel Tools Portable grinding tools need to be equipped with safety guards to protect workers not only from the moving wheel surface, but also from flying fragments in case of breakage.
Portable Circular Saws Among professionals, the circular saw is probably the most commonly used power saw and perhaps the most commonly abused. Portable Circular Saw Safety Precautions Always wear safety goggles or safety glasses with side shields complying with the current national standard and a full face shield when needed.
Portable Circular Saw Safety Precautions For maximum control, hold the saw firmly with both hands after securing the workpiece. Portable Drills Available in a variety of types and capacities, portable power drills are undoubtedly the most used power tools.
Portable Drill Safety Precautions Check carefully for loose power cord connections and frays or damage to the cord. Pneumatic Tools Pneumatic tools are powered by compressed air and include chippers, drills, hammers, and sanders. Pneumatic Powered Tools Pneumatic power tools shall be secured to the hose or whip by some positive means to prevent the tool from becoming accidentally disconnected. Pneumatic Powered Tools The manufacturer’s safe operating pressure for hoses, pipes, valves, filters, and other fittings shall not be exceeded, The use of hoses for hoisting or lowering tools shall not be permitted. Pneumatic Tools A safety clip or retainer must be installed to prevent attachments, such as chisels on a chipping hammer, from being unintentionally shot from the barrel. Caring for the Compressed Air System Using pneumatic tools requires an efficient compressor system to adequately power the tools. Contaminates in the Compressor System The most common problem is water in compressed air All air contains a certain amount of moisture and impurities which can cause problems when it condenses in the air. For newest information you have to pay a visit internet and on internet I found this site as a finest web site for hottest updates. Always turn off any power tool you are using before setting it down on the floor or a table.
The purpose of this module is to teach you to work with your coworkers to eliminate the incidents caused by hand tools and portable power tools. At the conclusion of the class, each participant will take a written examination and complete a course evaluation.
Discuss concerns related to employees using their own tools and how to manage these concerns.
Improving our customer’s productivity and bottom line through better products, services, and customer service. The study, co-sponsored by the National Institute for Occupational Safety and Health of the US Centers for Disease Control and Prevention, revealed the most common occupational acute hand injury was a laceration (63%), followed by crush injury (13%), avulsion (8%), puncture (6%),fracture (5%), contusion (1%), and dislocation (0.1%).

Do not carry tools in a way that interferes with using both hands on a ladder, while climbing on a structure, or when doing any hazardous work.
Keep cutting tools sharp and cover sharp edges with suitable covering to protect the tool and to prevent injuries from unintended contact. Replace cracked, splintered, or broken handles on files, hammers, screwdrivers, or sledges. Ensure that the handles of tools like hammers and axes fit tightly into the head of the tool. Wear safety glasses or goggles and well-fitting gloves appropriate for the hazards to which you may be exposed when doing various tasks. Toyota Lift of Minnesota thanks Mike Graves and TMHU for all the material they make available to their dealer network.
This entry was posted in Safety, Service and tagged hand tool safety, hand tools, technician safety by Kyle Thill. Connect with us further!Sign up for our monthly Material Handling Newsletter and get a free forklift safety poster for doing so! These tools help us to easily perform tasks that otherwise would be difficult or impossible. If you interesting in "Hand and Power Tool Safety" powerpoint themes, you can download to use this powerpoint template for your own presentation template. Wrenches, including adjustable, pipe, end, and socket wrenches shall not be used when jaws are sprung to the point that slippage occurs.
Employees and employers have a responsibility to work together to establish safe working procedures. Floors should be kept as clean and dry as possible to prevent accidental slips with or around dangerous hand tools. Some examples: Using a screwdriver as a chisel may cause the tip of the screwdriver to break and fly, hitting the user or other employees. Employers should caution employees that saw blades, knives, or other tools be directed away from aisle areas and other employees working in close proximity.
Where this hazard exists, spark-resistant tools made from brass, plastic, aluminum, or wood will provide for safety. With enhanced tool performance comes the responsibility to address power-tool safety issues. There are several types of power tools, based on the power source they use: electric, pneumatic, liquid fuel, hydraulic, and powder- actuated.
Among the chief hazards of electric-powered tools are burns and slight shocks which can lead to injuries or even heart failure.
Gloves, if kept clear of rotating parts, and safety footwear are recommended during use of electric tools. Before an abrasive wheel is mounted, it should be inspected closely and sound- or ring-tested to be sure that it is free from cracks or defects. The spindle nut must be tightened enough to hold the wheel in place, without distorting the flange.
Because of their handiness and application to a wide range of jobs, drills often receive heavy use. A tool retainer shall be installed on each piece of utilization equipment which, without such a retainer, may eject the tool. Safety clips or retainers shall be securely installed and maintained on pneumatic impact (percussion) tools to prevent attachments from being accidentally expelled.
Working with noisy tools such as jackhammers requires proper, effective use of hearing protection.
Screens must be set up to protect nearby workers from being struck by flying fragments around chippers, riveting guns, staplers, or air drills. Several basic guidelines should be followed to insure efficient and continued operation of the compressor. To ensure the best connection, clear any dirt off the nipple before connecting the air hose to the tool. Many power tools may not seem loud but prolonged exposure to an noise can cause hearing damage. Running through Toyota Material Handling’s training articles, I found this from Mike Graves.
The risk of a hand injury was significantly elevated when working with equipment, tools, or work pieces not performing as expected, when using a different work method to do a task, doing an unusual task, being distracted, and rushed.
Occupational category, job experience and safety training were found to alter several of these risks. For example, do not use a slot screw drivers as a chisel, pry bar, wedge or punch or wrenches as hammers. If working on a ladder or scaffold, tools should be raised and lowered using a bucket and hand line.
However, these simple tools can be hazardous and have the potential for causing severe injuries when used or maintained improperly. For viewing only, you can play with our flash based presentation viewer instead of downloading the ppt file.
Impact tools, such as drift pins, wedges, and chisels, shall be kept free of mushroomed heads. If a hazardous situation is encountered, it should be brought to the attention of the proper individual immediately.
If a wooden handle on a tool such as a hammer or an axe is loose, splintered, or cracked, the head of the tool may fly off and strike the user or another worker.

A lower tensile strength means the metal has less strength or resistance to tearing apart when stretched under test conditions.
Maintenance management professionals and technicians responsible for specifying and using power tools have a responsibility to check out a tool’s safety features, then ensure that manufacturer safety precautions and common sense are followed at all times.
The user and the tools are protected in two ways: by normal insulation on the wires inside, and by a housing that cannot conduct electricity to the operator in the event of a malfunction. Choosing the wrong accessory or using an accessory incorrectly can result in serious injury.
Unplug tools before installing, adjusting and changing any accessory or attachment of any kind. The main one is the danger of getting hit by one of the tool’s attachments or by some kind of fastener the worker is using with the tool.
When using pneumatic tools, employees must check to see that they are fastened securely to the hose to prevent them from becoming disconnected. You will also learn to control or eliminate hazards associated with hand tools and portable power tools. Special attention toward hand and power tool safety is necessary in order to reduce or eliminate these hazards. The wooden handles of tools shall be kept free of splinters or cracks and shall be kept tight in the tool. It also means that these tools are softer, wear down more quickly than ordinary steel tools, and have to be dressed more frequently. They should understand the potential hazards as well as the safety precautions to prevent those hazards from occurring. Disconnect tools when not in use, before servicing, and when changing accessories such as blades, bits and cutters. Care must be taken to assure that the spindle wheel will not exceed the abrasive wheel specifications. Don’t wear loose clothing, jewelry or dangling objects, including long hair, that may catch in rotating parts or accessories.
Eye protection is required and face protection is recommended for employees working with pneumatic tools.
Hose and hose connections used for conducting compressed air to utilization equipment shall be designed for the pressure and service to which they are subjected. A short wire or positive locking device attaching the air hose to the tool will serve as an added safeguard. When the tool is connected, check the hose and all connections for leaks or damage before using the tool. Graves again, I ask that our people and anyone [myself included] who uses hand tools remember the points made here. Bureau of Labor Statistics estimates that approximately 110,000 workers with hand and finger injuries lose days away from work annually – second only, to back strain and sprain.
Impact tools such as chisels, wedges, or drift pins are unsafe if they have mushroomed heads.
Due to the possibility of a wheel disintegrating (exploding) during start-up, the employee should never stand directly in front of the wheel as it accelerates to full operating speed.
When you start the saw, allow the blade to reach full speed before contacting the workpiece. When installing or changing a blade, be sure the blade and related washers and fasteners are correctly positioned and secured on the saw arbor.
To better understand the risk factors for hand injuries and to help reduce their occurrence, researchers at the Liberty Mutual Research Institute for Safety, in collaboration with colleagues at the Harvard School of Public Health conducted a study of occupational acute hand injuries.
Injuries included laceration (deep jagged cut), crush, avulsion (the tearing away or separation of part of the body, resulting from an accident), puncture, fracture, contusion, amputation, or dislocation.
Before starting a circular saw, be sure the power cord and extension cord are out of the blade path and are long enough to freely complete the cut. When making a partial cut, or if power is interrupted, release the trigger immediately and don’t remove the saw until the blade has come to a complete stop. Researchers examined seven potential transient (changing) risk factors in the occurrence of acute traumatic hand injury at work. Of the recruited subjects, 1,166 subjects (891 men, 275 women) participated in a telephone interview within approximately two days of their injury. Filters, regulators, and lubricators should be used to keep the air system working at its best. The study found that the risk of hand injury was significantly elevated when equipment, tools, or work pieces did not perform as expected, when workers used a different work method or performed an unusual task, and when workers were distracted and rushed. A sudden jerk or pulling on the cord can cause loss of control of the saw and a serious accident. Further, the results indicate that glove use significantly reduced hand injury risk by 60 percent. Is the speed marked on the blade at least as high as the no-load RPM on the saw’s nameplate?
Be sure to use the proper size air hose and fittings to keep air pressure at a maximum throughout the entire line. Forcing the drill can cause the motor to overheat, damage the bit and reduce operator control.

Baking tools online shop india 18
Tools direct tanger outlet 501
Air impact wrench how to use
Power tools for sale singapore furniture

Comments to «Power tool safety pictures powerpoint»

  1. ismayil writes:
    Saw's 12-inch blade is backed kill two birds (track saw and cordless) with doors.
  2. ZARATUSTRA writes:
    Tool comes with very good, clear.
  3. SeNINLe_SeNSIz writes:
    From the stick so you when both saws are powered by 4ah batteries little.

2015 Electrical hand tool set organizer | Powered by WordPress