10.01.2016

Wiring a hunter ceiling fan with remote price,wall fan gold coast,best quiet bathroom exhaust fan with light india,ceiling fan repair parts vinyl - PDF Review

Author: admin  //  Category: Big Ceiling Fans


My issue is that after buying a Hunter Universal ceiling fan remote (model 27208) for my new Hampton Bay ceiling fan (model 54-CL), the remote doesn't seem to work. SAFETY NOTE: Before you work on wiring devices, turn off the circuit breaker(s) or remove fuses associated with all circuits being worked with.
I hope this helps Ervinsean, let me know if we can do anything else to help you with your project!
To post questions, help other DIYers and reduce advertising (like the one on your left), join our DIY community.
I have recently bought a Hampton Bay Remote with Wall Switch, I have installed it to a Hunter Ceiling Fan. As I said that the two room is sharing power, will 15 amp breaker enough to run both room? I have to take off for a few hours so I'll post this diagram showing the daisy chain method, others here can help you if this is still confusing. Those combination devices usually have a single common screw for the power in and three separate screws for the controlled loads, so only one power connection is necessary. Ok that being the case you will just connect the single pigtail you already have to the common terminal of the combination device then just connect the switched wires as shown in the diagram.
Twin and earth wiring is required for all installations except those using a double wall control. However, If in doubt with any part of the installation procedure then please contact a qualified electrician.


Ia€™m sorry to hear about your wiring issues, but we should be able to clear things up in a jiffy. The smaller a€?Fan outa€? should be connected to the black wire that comes out of your ceiling fan. You can do that on a combination type switch either by daisy chaining from from switch to switch using the backstab holes in the back or by adding two more pigtails to the black wires and connecting those to the two switches for the light and fan. Also assuming this all worked before you added the ceiling fan you simply miswired something and the breaker tripped. If you chose to add pigtails to the wire nut (6 wires total) it will get rather difficult to get all the blacks into one wirenut for most DIY. The black wires I show connecting the switches will not be necessary so just look at them as internal to the switching device.. Your voltage detector should be tested on a live circuit first to confirm that it is functional before use. The red a€?light outa€? should be connected to the (usually blue) wire coming out of your ceiling fan that leads to the light kit (if applicable). Incoming power is one of the black wires connected in the wirenut that has three black wires in it. The white a€?Common outa€? should be connected to the white wire coming out of your ceiling fan.A  If for some reason your fan does not have these colors please provide us with the UPC code (this can be found on top of the fan motor housing on a small inspection sticker. If you feel that you lack the knowledge or skill to complete this project please call an electrician.


With the a€?outa€? wires connected correctly we can narrow things down to the wires coming from your ceiling. The other black is probably a secondary hot line from a previous installation where a hardwired control for the fan and light was used. Please be sure you have read and understand the installation instructions for your devices.
You should have the white wire from your ceiling connected to the fatter white wire on the receiver, the green wire connected to the green screw, or green lead from your bracket, also tied into the green lead from the ceiling fan motor. When you install your combination switch in that single gang box you need to get incoming power to each switch.
You can do that by getting two more pigtails and adding them into the wire nut with the blacks then connecting them to the other two switches along with the existing pigtail. Or you can connect that one pigtail to a switch and then use the backstab holes to daisy chain (connect together) the other two switches to that single pigtail.



My ceiling fan is making a scraping noise
Kid ceiling fan light kit 5m


Comments to «Wiring a hunter ceiling fan with remote price»

  1. Ilqar_10_LT_755 writes:
    These fans helps you never have to be concerned about forgetting to turn them off and reduce.
  2. VUSAL writes:
    Meaning heat is distributed evenly around alter the dip switches added.
  3. pakito writes:
    Can also turn off your primary you'll enjoy about Kichler® Ceiling fan and light, the.
  4. Becham writes:
    Fans for agriculture and livestock offer and even with.