29.12.2014

Fan light remote control wall switch outlet,wiring a ceiling fan speed control kit,convert ceiling fan to low profile 8gb,cost of a c fan motor - New On 2016

Author: admin  //  Category: Childrens Ceiling Fans


This page is about Ceiling fan pullchains, remote controls, Remote kits, Capacitor-stepped wall controls, Solid State speed controls, Transformer-based controls, Computerized wall controls, Dimmer switches, and more. To post questions, help other DIYers and reduce advertising (like the one on your left), join our DIY community.
Can someone tell me the wiring schematic for a Harbor Breeze ceiling fan remote control unit? I connected the black power lead to black ceiling fan lead plus 2 black leads on the remote antenna unit for a total of 4 black leads connected together. I connected the white neutral lead to white ceiling fan lead plus 2 white leads on the remote antenna unit for a total of 4 white leads connected together.
I connected blue cf lead to blue lead antenna unit for a total of 2 leads connected together. The light works fine from the hand remote, off and on, no problem but I can not turn off the fan from the hand remote or the HI, MED, LOW does not work from the hand remote. The ceiling wires should connect to the ones on the remote labeled L (black) and N (white). If you have a pull chain switch the pull chain switch for the fan should be set to high for the fan to work properly by the remote. I have another remote control fan light in another part of the house about 35 feet away and the two remotes are competing with each other! Many, many ceiling fans offer wireless remote controls very similar to that of a television or garage door opener.
Many manufacturers and retailers offer 3 or 4 speed wall controls that are hard-wired, that is they wire in place of a wall switch and directly regulate the current flow to the fan.
Some manufacturers and retailers also offer controls that, as opposed to having distinct separate speeds, offer an infinitely variable selection of speeds. Similar to capacitor stepped controls, transformer-based controls offer 4 or 5 distinct fan speeds.


If you haven't noticed, other than remotes, all of the wall controls mentioned thus far, require separate wiring if you wish to control both the fan and light separately from the wall.
These controls are handheld and offer 3 or more fan speeds, light control and dimming, reverse of the fan motor, and occasionally other features.
The most common and universal wall controls use capacitors to set 3 (or 4) distinct speeds. They are compatible with most or all ceiling fan motors, and are quiet, although some produce an almost inaudible humming sound. Many homeowners install ceiling fans to replace light fixtures where there is only one switched hot lead, and do not wish to pay an electrician to add another. The downsides are that if the remote is lost or broken, the fan is unable to be controlled, also the majority of remote ceiling fans use inexpensive electronics and are unreliable and break down. Most ceiling fans sold currently use 16 pole spinner motors which are incompatible with solid state speed controls.
And so some fan companies offer a wall control which only requires one hot lead, yet offers separate switching of the light and fan. If the fan has light attached, and the lights are wired to a separate switch from the fan motor, then a dimmer switch may be installed to control the lights only. Only fans with 18 pole motors (and other compatible designs) can be used with solid state controls.
They have the same advantages as capacitor-type controls, plus some are built to operate higher amounts of current and therefore control more than one fan. If the fan has no light, you simply wire it in place of the wall switch controlling the fan.
These include American-made ceiling fans, those with American-style motor designs (18 pole stack motors such as the K55), and some higher quality industrial fans. The disadvantage is that they usually mount on the surface of the wall rather than inside an outlet box, and therefore are ugly.


If the fan has a light, but the motor and light are controlled by separate wall switches, again, you simply wire it in place of the wall switch controlling the fan. Most fans will have an indication in the manual whether or not they can be used with solid state speed controls. They wire in the same fashion as capacitor controls and solid state controls, requiring a dedicated hot lead to the motor(s). If the fan and light are controlled by the same wall switch a third wire will need to be added to offer an independent power source for the motor and light. The advantage of solid state controls is the infinite selection of speeds, also solid state controls are often made to higher current ratings so that more than one fan can be operated by the same control.
Most capacitor type controls can only operate one fan per control, so multiple fans require multiple controls.
In all cases the wall control wires in place of a standard light switch, and the fan hooks up just as the ceiling light did with only two wires. Capacitor controls are commonly identified by having 3 or 4 distinct speeds, instead of infinitely variable speed selection. They wire in the same fashion as capacitor-type controls, requiring a dedicated hot lead to the motor(s). Each control can only be used with the specific fan, none other, and one control operates one fan only. Some companies offer kits, similar to the remote kits, in order to add this feature to a standard ceiling fan.



Honeywell high velocity floor fan walmart
Bathroom fan vent leaking
Cheap flooring for man cave


Comments to «Fan light remote control wall switch outlet»

  1. 202 writes:
    Design possibilities, any accessories desired ceiling.
  2. Eshqim writes:
    Fan might also save your and then unscrew the screws or nuts holding the installing the.