27.01.2013

Ceiling fan wiring diagram with light kit v3.0,ceiling fan with light low ceiling,aloha breeze 30 ceiling fan - Good Point

Author: admin  //  Category: Victorian Ceiling Fans


As I said that the two room is sharing power, will 15 amp breaker enough to run both room? I have to take off for a few hours so I'll post this diagram showing the daisy chain method, others here can help you if this is still confusing.
Those combination devices usually have a single common screw for the power in and three separate screws for the controlled loads, so only one power connection is necessary. Ok that being the case you will just connect the single pigtail you already have to the common terminal of the combination device then just connect the switched wires as shown in the diagram. Copyright © 2012 All trademarks are the property of the respective trademark owners. The house I moved into had a ceiling fan in the bedroom that was hooked up to a dimmer light switch. What I'd like to do is split it so the fan motor is toggled by the normal switch, and have the lights controlled separately on the dimmer.
I'm a complete beginner at this type of stuff, so I took some pictures and drew up a basic diagram. I assume I need to split the black wires, and possibly use the orange one to power the other switch after I split them?
Also if anyone is up for explaining, I'd love to know why those 4 wires are crimped into that little connection.. Without knowing first hand what wires you have available to you to use in way of the current splicing there is no way to put into words the ability for you to splice the switching in.


Sorry I'm of no help, but sometimes it's best to call a lic elec in and have it done quick.
Twin and earth wiring is required for all installations except those using a double wall control. However, If in doubt with any part of the installation procedure then please contact a qualified electrician. You can do that on a combination type switch either by daisy chaining from from switch to switch using the backstab holes in the back or by adding two more pigtails to the black wires and connecting those to the two switches for the light and fan.
Also assuming this all worked before you added the ceiling fan you simply miswired something and the breaker tripped. If you chose to add pigtails to the wire nut (6 wires total) it will get rather difficult to get all the blacks into one wirenut for most DIY. The black wires I show connecting the switches will not be necessary so just look at them as internal to the switching device.. Most of the wires are black and they're all joined into a weird little connection (see the picture).
Your best bet is to have someone look at it firsthand and either tell you how to at that point or have them perform the job. Whatever you do is don't take apart any splicing unless you are very comfortable knowing what you're doing.
Incoming power is one of the black wires connected in the wirenut that has three black wires in it.


Since both the light and fan work fine on one switch, it would seem everything needed is already in that wall box, so can you explain why I may need to run another wire to the light? I've been called to many a home from someone that tried to do some style of work only to have circuit not work. For now, I disconnected the dimmer switch and put everything on the normal switch so that the fan works properly. There is a purple wire coming down from the ceiling that goes into the other connection on the switch. When you install your combination switch in that single gang box you need to get incoming power to each switch. You can do that by getting two more pigtails and adding them into the wire nut with the blacks then connecting them to the other two switches along with the existing pigtail. Or you can connect that one pigtail to a switch and then use the backstab holes to daisy chain (connect together) the other two switches to that single pigtail.




High velocity fan amazon kindle
Buying a ceiling fan with light fixture


Comments to «Ceiling fan wiring diagram with light kit v3.0»

  1. PUBLIC_ENEMY writes:
    About this residence addition, never fret, with the developments and the elements.
  2. TELEBE_367a2 writes:
    Can be employed in high- and low-ceiling constructed-in heaters, normally infrared.
  3. EXPLOD writes:
    For them is you do not know light in the space mention in the solution specs, which signifies.
  4. pobrabski writes:
    Efficiency and comfort only the ideal name air conditioning, ceiling fans, refrigerators.