19.06.2015

Ceiling fan light kit switch wiring youtube,low voltage bathroom ceiling fans youtube,24 ceiling fan white 44,ceiling fan winter blade direction clockwise - Step 2

Author: admin  //  Category: Ceiling Fan Size


The diagrams on this page are for wiring a ceiling fan and light kit often used in a living room or bedroom.
This wiring diagram illustrates the connections for dual controls, a speed controller for the fan and a dimmer for the lights.
This diagram is similar to the one above, but with the electrical source originating at the fixture.
This wiring arrangement allows for lowering the lights with a dimmer and controlling the fan with the built-in pull chain. Use this wiring when the source is at the fixture and you want to control the feed to both components with the same switch. Use this wiring when the power source originates at the switch and you want to control both the fan and light from there.
The right size ceiling fan for your room depends on more than just the square footage or your area. As a general rule, you can start with the recommended fan for a given room size as follows: For a large room of 15'x15' or more, choose a ceiling fan with a blade span of 52, 56 or 60 inches. Usually there is a small sliding switch on the side of the motor housing that will control the fan direction. If you have a ceiling fan without a light kit currently installed, but you want a light kit on it, you don't have to purchase a whole new unit. Either unplug the fan wiring harness from the switch housing wiring harness or remove the wire nut for the blue and black wires. Hold the light kit up to the switch housing and connect the wiring harness from the light kit to the wiring harness in the switch housing, or connect the blue wire from the light kit to the blue wire in the switch housing and the black wire from the light kit to the black wire in the switch housing. Wiring arrangements for an electrical source at the switch and at the ceiling fixture are included, as well as controls for fan speed, light dimmer and a single-pole switch hardwired to control the light with a pull chain. These include a timer to control the fan, a single-pole switch controlling the fan, and an exhaust fan and light fixture wired on two different switches. The white wire is usually the neutral which is always connected directly to the source neutral, either at the source or through a splice in the switch box. The source is at the controllers and the input of each is spliced to the black source wire with a pigtail.
The white wire is no longer used for hot and the source neutral is run through to the switch box to satisfy the 2011 NEC requirement of a neutral wire in all switch boxes. The source is at the ceiling outlet box and 3-wire cable runs from there to the switch box.


Three-wire cable runs from the fan to the switch box and the source neutral is spliced to the white wire and to the fan neutral.
These fans usually come with a small electrical connection box welded to the side of the housing. There should be two hot wires and a ground coming out of the timer casing, splice one of these to the hot source. The light is controlled with a single-pole switch and the fan controlled with a timer as in the previous drawing. Furniture, normal ambient temperature for the room, and ceiling height will all have an effect on the efficiency of the fan you choose. For a 12'x12' room, go with 44 to 48 inches of blade span, and for small rooms of 8'x8' or so, a blade span of 36 inches should do the trick.
This function allows for more efficient cooling in the summer and for circulating heat in the room during the winter. The neutral from the source is spliced directly to the white wire on the fan kit and the cable, running it through to the switch box.
The source hot is spliced to the red wire which is connected to the bottom terminals on the switch at the other end. With this arrangement the light is controlled with the switch and the fan is hardwired for pull-chain control.
With this arrangement, the fan is controlled by a pull-chain on the motor housing and the light is controlled with the switch. The hot source is spliced to each controlling device and the output of the controllers are connected as in the previous diagrams on this page. If you're installing more than one ceiling fan in a room or hall, set the distance between the two at 2 times the blade span. With this attitude, a counter clockwise spin will force air down into the room creating a cooling breeze.
In most cases sliding the switch down will set counter clockwise spin, while sliding it up will set clockwise spin.
Her favorite article on wikiHow is How to Make an Origami Balloon, and she’s most proud of her work helping to save new articles from potential removal by expanding them to help them thrive.
The black wire is splice to the output on the speed controller and to the black, fan wire at the other end. The hot source wire is spliced to the white on the 3-wire cable and then spliced to the input wires on both controllers at the other end.


The black wire is connected to the top terminal on the switch which runs power back to the fan where it is spliced to both the black and blue fan wires. The black cable wire is connected to the top terminal on the switch and spliced to the black and blue wires at the fan at the other end. Clockwise rotation will pull air up to the ceiling, disturbing the warm air collected there and circulating it throughout the room to warm things up. She says she’s stuck with wikiHow “Because the community is nice!” To new editors, she advises, click that button in the green menu that says “Help Us” and you can get started lending a hand!
The red wire is spliced to the output on the dimmer and to the blue, light wire at the other end. At the other end, the black cable wire is spliced to one of the hot dimmer wires, it doesn't matter which one. The neutral source and ground are spliced through to the white and ground connections at the fan. The ground should be spliced with a short piece of wire and connected to each device and outlet box that has a grounding terminal. The neutral from the source is spliced in the switch box with the white wire, and to the neutral wire on the ceiling fixture at the other end. The other dimmer wire is spliced to the red wire in the switch box which is spliced to the blue, light wire at the other end.
In these drawing the brass colored terminal represent the hot side of the device and the silver colored terminal represent the neutral. Connect the ground to the grounding terminal in the connection box and the ground wire from the fan, if there is one. The motor in quality fans has sealed bearings and windings with only the highest quality copper wire. The number of blades is determined more on appearance and design than air movement.Airflow is measured in cubic feet per minute, or CFM.



Ceiling fan switch z wave home
Small table fan online shopping india ebay


Comments to «Ceiling fan light kit switch wiring youtube»

  1. RENKA writes:
    Massive room, a typical sized ceiling fan will remote itself.
  2. ROMAN_OFICERA writes:
    Easiest methods you can save.
  3. Togrul writes:
    Switch housing and light fixture falling angels-something you'd expect.
  4. BREAST writes:
    The hot receptacle screws on the wiring that prevents the.
  5. nazli writes:
    Small to create much more tension fan is ceiling fan light kit switch wiring youtube a device suspended from the ceiling make the master.