Fine Woodworking Circular Saw Review,Lapstrake Outboard Skiff,Woodwork Tools List,Building Plans For Wooden Benches - Easy Way

07.06.2014, admin  
Category: Woodworking Plans Online

How to Make Perfect Crosscuts and Rip Cuts with a Circular SawA few minutes spent constructing these two simple, homemade jigs will allow you to make straight, even crosscuts and rip cuts with a portable circular saw with ease.
Circular Saw Rip Fence: Unplug the circular saw and clamp a straight board to the base to act as a fence. Position the guide on a scrap board with the base of the circular saw pressed firmly against the guide. A rip guide allows you to use a circular saw to make long straight cuts in boards and plywood.
Clamp a board to the saw base, measuring from both the front and back of the blade so the fence and blade are parallel. When using a miter saw outdoors, it’s important to have a long, rigid table to support the saw and work. If you run the crooked edge of a board against the table saw fence, you'll still have a crooked board when you're done. Table saws excel at ripping long boards, but it's dangerous to do it without supporting the board as it leaves the saw. This will trim off the excess cleat on one side so the guide is the exact width of the saw.
Become a member today to enjoy our complete library of videos and woodworking information online. Resident tool guru Roland Johnson takes a close look at midsize cabinet saws in this issue.
FWW editor Tom McKenna has unearthed a bevy of ingenious homemade woodworking machines in this issue’s Looking Back department. Learn the right way to prepare for, and glue up your woodworking projects—from start to finish. Bosch's newest 12-inch sliding miter saw doesn't have slide tubes so you can put it right against the wall.
There was one scathing review from a trim carpenter (I don't remember which site I was on) but this guy apparently knew his stuff and was throughly disappointed with the fact that the size of stock was so limited on one side of the saw due to the engineering limitations. NewZealander writes: yeh but the kapex is only a 10" saw , good for small stuff - but as soon as you try to cut something bigger like posts & cutting 2-3-4 studs at once - its a waste of time . I'm looking at getting a new slide compound mitre saw now & the bosch hasnt hit New Zealand yet or for some time i imagine , looks like it will have to be the Milwaukee 12" .


Stranded writes: I have a Festool Kapex mitre saw and I've been told by a course instructor that it is the only manufacturer whose saw will cut consistently true mitres without operator corrections being made, so I would be interested to know if others, including Bosch, are gaining on Festool's quality.
Thanks for the additional information, I honestly hope that the saw is a roaring success and sparks more innovation! NCRon writes: I wanted to buy this saw so contacted Bosch customer service to see about dates. BuckeyeRob writes: You should also point out that this saw will only be available with a 220V motor. The advantage of there being no rails behind the saw is a big one, but this is NOT the first SCMS to feature this, Hitachi has had their side rail saws out for quite some time, and you lose almost nothing behind the saw. Still, there are a lot of other sweet features on this saw, and I'm all for new innovative ideas on our tools.
The problem with making repetitive narrow rips on a table saw is that the blade guard and the fence are too close together to allow a push stick to fit between them. If you have a cast iron bed on your table saw, you could buy a featherboard that attaches with super-strong magnets that make it simple to position and adjust. You can cut plywood on sawhorses with pretty good results, but when you want really smooth finish cuts on an expensive sheet, always cut on the floor. The trick to a perfectly straight cut is to clamp a straightedge to the plywood and use it as a guide for your saw. Then run the straight edge of the plywood against your table saw fence to make a perfectly straight edge on your crooked board. Listen in on a Shop Talk Live podcast where he talks about the most important features to look for in a new saw.
In a small stroke of brilliance bosch put a smaller hex wrench on the other end of the blade wrench that fits some of the saws's other adjustments. Whether you collect hand planes or seek out the latest and greatest in power tools, our expert tool addicts will keep you in the loop with news, reviews, and commentary on the latest in woodworking tools.
Even if you own a table saw, sometimes it's easier to rip large sheets of plywood with a circular saw.
Position the jig on a scrap board, hold the circular saw firmly against the fence of the jig, and cut through both board and one arm of the jig. His fascination with motors and gears goes beyond woodworking, he's also an enthusiastic hot-rodder who likes to restore old cars, and is the author of Automotive Woodworking (Motor Books International, 2002).


Set the blade of your circular saw to the lowest depth and fit it with a fence set to rip ¾-inch of wood from the 4x4.
You can crawl right across the plywood, keeping the saw moving forward in one fluid motion. There are nine detents for common miter settings and the semicircular ring that houses the detent notches is adjustable for bringing the saw to square. I guess if my shop were so small, that I couldn't live without an extra 2-3 square feet, maybe I would consider this saw. To use the crosscut guide, mark the board where you would like it cut, position the guide so the cleat is even with the mark, hold the jig firmly against the board, and make the cut, keeping the saw base against the guide fence. Although we’ve seen it on past Bosch miter saws, I really like the upfront bevel control that eliminates reaching around the back of the saw for bevel adjustments.
A circular saw's blade is not large enough to cut through the entire 4x4, so you must flip the 4x4 over and cut through the remaining thickness, again letting the fence ride along the side. I tested the saw with a number of cuts and materials and it perfomed exceptionally well right out of the box. Also note that a circular saw cuts on the upstroke, which often splinters the top edge (veneer) slightly. As a result, you end up with two or three square feet of wasted space behind the saw—most woodworkers I know would rather put that space to better use. Bosch’s new saw is accurate, the controls are precise and intuitive, and the space-saving design is icing on the cake. Instruct your helper to simply support the plywood, flat palms up, level with the saw bed, and let you do all the work. I did swap the Bosch blade that comes with the saw for a CMT version with 90 teeth because it had less runout than the factory blade. It will yield slightly when you push down on the saw handle, which varies the depth of cut by .050 of an inch.



Plans For Outdoor Swing Frame
Industrial Wood Cutting Equipment
Wood pallet outdoor furniture plans


Comments to “Fine Woodworking Circular Saw Review”

  1. KRUTOY_BAKINECH:
    Wooden crafting initiatives which might project over and over until you.
  2. aH:
    Dozen or so primary mission templates amazing first-time woodworking pumpkin Block Heads Challenge Ideas - If there are odds.