Using a single slide ($8 to $20 per pair) in the center of the drawer reduces hardware costs.
When you use only one slide per drawer, you reduce the weight-carrying capacity to less than half that of a similar drawer with two slides. GOFAR Services, LLC - Appliance Repair Houston, TX - Chapter 7MAYTAG "NEWTON" MACHINES (for Maytag Performa and Atlantis models,see Chapter 7a)NOTE: Chapter 2 covers problems common to almost all washer designs. So i did about 9 sketchup designs, and ended up with two I liked - one face frame design and one "european" non-face frame design. I also considered using plywood in the design, but decided to go with solid cherry for the whole unit.
I decided that I would drop the BluRay storage underneath, as I have an outlet on the wall that will house the unit. The TV also needs to be about 44" off the floor (centre of screen) to accomodate the optimal viewing area, so that outlet was just in the way. These instructions are intended for wood and faux wood blinds that are installed with what we call box brackets (see photo below). When you ordered your blinds you should have chosen between an inside mount and outside mount.
If your window frame is drywall rather than wood, or if your window frame doesn’t have wood behind the drywall, you should use drywall anchors. If you need more help installing your blinds, we have friendly blinds experts who’d be happy to assist you by phone, email or live chat. You can also find more resources on our installation page, including video installation guides. We share our favorite DIY projects, home decor tips, window trends and lifestyle products to make your world a beautiful place.
THIS chapter covers only diagnosis and repairs peculiar to CERTAIN Maytag-designed machines. I spitballed some movement concerns I had with the community (thanks for the advice Steve!), and decided to go with the "sleeker" version with no face frame. I'd also recommend cutting some hidden ventilation holes where your components will be housed. A  A If you have a FWW membership, check out this article which shows an integrated french cleat.
That would be helpful to those that don't have the membership but do have print or back issue DVD. We’ve got a step-by-step guide to tell you how to install wood blinds and faux wood blinds.
There may be some slight variations when installing your blinds, so consult the paper instructions that arrived with your order as well. We’ll be placing screws in two diagonal holes on the side of the bracket (not the ceiling). Install any included center support brackets in line with your other brackets and slightly off center so they will not interfere with mechanisms in the headrail.
Attach brackets to valance by inserting the notch into valance groove at a 45 degree angle. Twist clip straight to secure. Unwind your cords and lower your blinds by pulling your cord toward the center of the window. Use your measuring tape to make sure the distance between your mark and the window opening is even on both sides and that they are level.
These pieces hold your blinds to the door so they don’t swing when you open and close the door. Fully lower your blinds and insert the hold down bracket into the hole in your blind’s bottom rail.


If you’d like to raise your blinds, just pop the bracket out of the rail to allow your blinds to move freely. As a newlywed, she’s on the hunt to outfit a new home with all things handmade, preppy and eclectic.
If you do not read Chapter 2 thoroughly before you read this chapter, you probably will not be able to properly diagnose your machine!!!!7-1 BASIC OPERATIONThe design uses a reversing motor, which is belted to both the pump and the transmission, using two different belts. Sometimes the hardware for your whole room is in one box even if your blinds arrived in separate boxes.
Don’t latch the door, but line up your bracket so the door is even with the window edge when closed. Install this in alignment with the other 2 brackets and slightly off center so as not to interfere with any mechanisms inside the headrail. Hook the top of the clip onto the headrail and then press the bottom of the valance in to snap on the bottom of the clip. Walking in the footsteps of Martha Stewart, she’s happiest when she’s crafting or whipping up a new recipe; although nothing beats curling up with a good book and some Girl Scout Cookies. When viewed from the top, the motor turns clockwise for the agitation cycle, and counterclockwise for the spin cycle. During agitation, the brake keeps the transmission casing from turning, and the drive pulley turns the transmission shaft. During the spin cycle, the brake releases and the whole transmission starts slowly spinning around.
At the end of the spin cycle, the motor stops and the brake brings the basket to a stop. In the late '80's, Maytag redesigned the transmission. The result is the "orbital" transmission, which has just a few moving parts and is serviceable in the machine.
Springs attached to the motor mounting plate keep tension on the belts. The pump reverses with the motor, but there is no recirculation. Follow the safety precautions described in section 1-4(2).To open the front of the cabinet, remove the two screws at the bottom of the front panel. In order to diagnose these machines, you need to keep the lid up far enough to look inside, without tripping the lid switch. Replace as described in section 7-10. With the machine in "spin," look at the pump pulley beneath the machine with a mirror.
If it is spinning, but water is not pumping, check for a clog in the hose between the tub and pump.
If you hear the motor buzzing, but it doesn't start in either or both directions, test the capacitor (if any) and starting switch as described in sections 2-6(e) and 7-8.
If it does start with the load removed, turn the pump and transmission pulleys by hand, in both directions, to see which is locked up. Note that the transmission pulley will normally be very stiff when turning it in the clockwise direction, as you look at the bottom of the washer.6) If the washer spins but does not agitate, check the agitator splines as described in section 7-11. See section 7-13.7-4 PUMP AND PUMP BELTRemove the pump belt and check to see if the pump will turn freely by hand. Test as described in section 2-6(e). Maytag motors have a piggyback centrifugal starting switch.
To make matters worse, the motor wire colors do not always correspond with the colors marked on the switch. Whenever removing the motor or switch from the machine, mark which wires came off which of the switch terminals.Draw a picture if you must. Make sure you differentiate in your notes between a motor wire and a wiring harness wire of the same color, and where each goes on the switch. If the drive motor does not start, try replacing the starting switch as described in section 2-6(e). If the motor STILL doesn't start, replace it. To remove the motor, first remove power from the machine.


Remove the plastic water shield from the motor, and mark and remove the wires. Remove the drive belts. Remove the four motor baseplate screws and lift the motor and baseplate out of the machine. Installation is the opposite of removal. Make sure you check the box that the new motor comes in for a wiring diagram.7-9 TRANSMISSIONI do not recommend the novice trying to replace a transmission in a Maytag washer, for several reasons.
And by the time you throw in a brake package, stem and seal kit, etc., it is usually just not worth it. If both break, there will be NO tension on the belts and in addition, the motor shaft will probably be hitting the washer baseplate, causing a heck of a racket. The roller tracks can get clogged up with dirt, soap deposits or other obstructions. Lubricate the rollers and tracks with a little wheel bearing grease. Examine the condition of each belt as described in section 2-5(a). Pump belt tension is explained in section 7-4.7-11 AGITATORMost Maytag washers have an agitator that lifts directly out. These models have a rubber stop ring around the agitator shaft at the bottom of the splines. Block up the tub so the tub remains in line with the cabinet. Beneath the washer, in the center, is the brake package. The brake package changes the machine from the spin to the drain cycle and back when the motor reverses. It also brakes the spinning basket at the end of the spin cycle or when the lid is lifted. The brake lining is normally lubricated by a few drops of oil. If the lining gets too dry, it can start squeaking at the very end of the spin cycle, when it is braking the basket. YOU MAY HURT YOURSELF OPENING IT, AND IT IS IMPRACTICAL FOR YOU TO TRY TO REBUILD IT YOURSELF. BRAKE PACKAGE REMOVALRemove the center screw from the driveshaft. This will help you to thread the brake package into the base plate without cross-threading it.
With the tub blocked up, grab the bottom of the transmission casing and move it by hand until you can slip the brake package onto the splines.
If you don't, you will be trying to overcome brake pressure to turn the package.Turn the transmission and brake package until the brake package is hand tight in the baseplate. While holding the transmission so it doesn't turn, run the drive pulley up as tight as you can by hand onto the helical shaft.You will see a drive lug on the pulley that corresponds to the shaft drive lug.
Then turn the pulley gently clockwise until you just barely begin to feel the brake spring pressure.The shaft lug should be at about 9 o'clock from the pulley lug. If not, adjust the shaft lug on the splines. The idea is to get the pulley to bottom out on the helical drive shaft just as the drive lugs touch. If it is not correct, you will hear the drive motor bogging down and perhaps tripping on the overload during the agitation cycle.7-14 DAMPER PADSThe damper supports the weight of the water in the tub. Mark the position of the nuts on the three eyebolts (Figure M-15) and remove the bottom nuts.
This will remove spring tension on the tub centering springs.Lean the washer back against the wall at an angle. Place a 4x4 wood block directly underneath the transmission pulley and lower the machine onto the wood block. If you hear the motor buzzing, but it doesn't start in either or both directions, test the capacitor (if any) and starting switch as described in sections 2-6(e) and 7-8.




Woodworking Plans Projects Magazine Uk
Woodworking Network Media Kit


Comments

  1. malakay

    The scrapes and discover to see how the shapes focused on green design.

    21.02.2016

  2. LEZBIYANKA

    Would offer net support individuals use their homes to influence about.

    21.02.2016

  3. crazy_girl

    Youngsters have had enjoyed hammering and.

    21.02.2016

  4. Glamurniy_Padonok

    Simple Woodoperating Projects) is well above something you will discover e-book in 2005, and rather Install Wood Center Mount Drawer Slide a lot has.

    21.02.2016

top