Building a wooden horse fence is ideal for keeping livestock and for giving rural property that barn-country appeal. Wood does eventually succumb to the elements and must be repaired from time to time, whereas vinyl fencing usually comes with a lifetime warranty when it is installed. A three-rail wooden fence creates an attractive, safe area for your horses to roam and graze.
Discuss your plans with any neighbors whose property lies along your proposed fence line to make sure your fence is on your property. Good to KnowTo build a durable fence that will last for years to come, pay special attention to the materials you use.
Spaced Picket: This is ideal for keeping children or pets in and defining boundaries, while achieving a distinctive look and aesthetic appeal. Shadowbox: This style uses alternating panels across the back and front to give the fence the same look on both sides. Using the same measurement as the length of your panels, stake out the line post locations. Measure on center from each corner post (from center to center of each post instead of from the edges) along the layout lines. When staking out line posts on a slope for a step method installation, you'll need a true horizontal measurement for post placement.
Use a 2-by-4 to extend from the proper tape measurement to the ground to locate the placement of the stake. When setting posts on a slope, set them so they're taller than you need for the panel so you can cut them to height just before the panels are hung. An easy way to make your post heights uniform on level ground is to run a string at the desired height from corner post to corner post, keeping the string.
Using a posthole digger or power auger, dig the holes 10 inches to 12 inches wide and 6 inches deeper than needed. Backfill each hole with 6 inches of gravel to drain water away from the bottom of the post.
Brace the posts using 4-foot sections of 2-by-4s nailed to the post diagonally and then nailed to stakes in the ground. Before the concrete sets, check plumb and alignment again, and make any necessary adjustments. Place each panel between the posts so that the ends of the panel come to rest in the center of the posts. If it's necessary for the two panels to butt together between posts (perhaps there's something in the way that prevents the setting of a post in the appropriate place, for example), attach a 3-foot cleat across the joints of the rails to provide additional support. Since the gate will endure more use and wear than any other part of the fence, use secure gateposts, strong hardware and a well-built and braced frame.
Assemble the frame with screws, ensuring that the corners are square by using a carpenter's square.
Place a 2-by-4 diagonally across the frame, from the top-latch side to the bottom-hinge side.
Face the gate frame with the same design as the rest of the fence using boards or pickets. Stain provides a durable finish coat, while still allowing the look and texture of the wood to come through.
Waterproofing sealer, or repellent, is the choice for woods, such as spruce, birch, hickory, red oak and poplar, that aren't resistant to decay and exposure to weather. I focus on building structures that are not only beautiful, but excellent value for the money and built to last. That is one of the reasons why I do all the work myself, so I can control the quality of construction and you don't have to deal with crews of workmen you have never met.
Below is my portfolio of fence photos, as well as pricing for fencing in the Los Angeles area and a detailed fence design guide.
My portfolio features photos of my wooden fences and privacy screening so you can get an idea of the styles and types of fencing I design and build. As a first step, I recommend that you look at lots of different fences to discover what you do and don't like. When you are ready to get started, contact me and we can set up an appointment to tour your location, discuss design options and establish a budget, so I can give you a detailed estimate. A basic fence costs from $15 to $45 per foot and include all materials and labor but may not include demo of your old fence or painting the new one. Custom fences cost from $45 to $85 per foot and include the cost of a custom design and using high quality materials and techniques. High end wood fencing is an investment in your property and costs from $85 to $150 per foot. If you are purchasing pre-made fence panels, remember to include the cost of on-site installation and additional materials (posts, concrete, hardware and brackets) in your budget.
This design guide provides information on how to create a great fence design which reflects the architectural look of your home and meets your needs for privacy and functionality. If your home has a distinctive architectural or artistic style, you may want to have your fence match it.
Craftsman & Greene and Greene Fences ~ One of the most popular Los Angeles area styles can be achieved with smooth planed wood assembled using simple decorative pegged joints. Modern, Asian & Contemporary Fences ~ For a modern or contemporary look, you can design a fence with classic clean lines with sleek trim and hardware. Mission, Spanish & Southwestern Fences ~ Start with natural wood posts and fence boards and accent them with period post caps or decorative rustic metalwork. Cottage, Colonial & Ranch Fences ~ I like to give a sophisticated look to the standard cottage fence with arches, custom fence board details and decorative post caps. Medieval, Tudor & Mediterranean Fences ~ I like to use large posts, beams and rails stained or painted a dark color.
Neighbors & Your Property Line ~ Before a design is approved, it is very important to obtain consensus with all your neighbors on the style, height, orientation (of the good and bad side) and finish of the proposed fence. View ~ A fence provides a natural way to obscure the surrounding neighborhood or highlight views of your garden. Wind ~ In areas that experience high winds, a more open design, extra bracing, and heavy duty hardware may be needed. Water ~ Excessive moisture (from rain, hosing down, sprinklers and deep shade) can lead to premature aging, structural damage from rot and musty smells. Materials ~ To maximize the life expectancy, the frame should be made of pressure treated lumber set in steel column bases. Finishes ~ Heat and light contribute to weathering, so a UV protective finish is important. Accessories & Built-ins ~ Trim, moldings, lattice, post caps, finials and fence art add to the uniqueness of your fence. Metalwork ~ Accents, such as copper post caps or blackened iron joining straps, can enhance the appearance of your fence or screening.
Lighting ~ The choice of lighting style and fixtures (such as lanterns hung from posts, mounted sconces, and spot lighting) can create an immediate sense of style. To make sure you are delighted with your custom fence or privacy screen -- you want to choose the right building material. The first type of wood to choose is for your framing -- the structure that holds your fence upright and to which you attach the fence boards.


Pressure Treated Wood ~ For hidden framing, I only use pressure treated lumber (see photo). Redwood ~ For visible framing, such as fence posts, cross pieces and railings you can upgrade to redwood for a better appearance.
Cedar ~ A soft, golden-tan wood (see photo) that offers good weather and termite resistance. If you need ideas and inspiration, clip magazine pictures, look through your vacation photos and keep an eye out for what you like in the neighborhood.
For more ideas or inspiration for your fence or privacy screen, you might be interested in these resources. This inspiring book has 150 photos of beautiful walls, in a range of archetectural and garden styles, that define and create space in your garden. This book features many inspirational photos and ideas for fences, gates, trellises and more. This book provides photos of 1,000 fences and gates of every type to give you lots of ideas and inspiration.
This book is packed with ideas and design styles to help you be inspired and find the right design for your yard or property. This book is an excellent source of ideas and offers over a hundred photos of a vast array of fences and gates. This book illustrates different fence styles and gate hardware to help you decide what you prefer. This site features two downloadable booklets that feature 25+ photos the major fences styles.
You can search the image archives at Google Images, Yahoo Images, MSN or your favorite search engine to find inspiration from architectural showcase homes, historical buildings and DIY projects. Unfortunately, since I build every fence from the ground up on site at your home, I do not make pre-made fence panels for others to install.
This small firm designs and builds artistic fences and gates in the Pacific Northwest and ships pre-made items overseas. Fine high end wood architectural pre-made fence panels and gates installed by a local craftsman in major cities, including Los Angeles. These kits are more expensive than welding your own pipe fence, but they are less How to Build a Wooden Rail Fence.
Below is some basic fence-building information, as well as a few twists that I Crosspieces can be made from wood, pipe, old steel fence posts, or even old bed rails. BNB Buildings offers the LOWEST PRICES IN TEXAS on all types of clear span welded and pre-engineered metal buildings.
Exclusive Ornamental fence dealership providing stronger square tubing construction for pickets and started business in 1997 selling used pipe and steel for fencing Making a pipe and mesh fence This article explains how to make a galvanized pipe and chain-link fence. Whether you are building a line fence, horse fence, cattle fence, corral, or gates, we can help you find the right fence pipe and the best price for all of your livestock Custom Built Pipe Fence for your Ranch or Farm to give it the Country or Western look. Wayne The first thing you need to work out is whether the fence is built on the boundary line. Horse fences are typically long, wooden plank structures painted white that decorate miles upon miles of green countryside. Ia€™m a city boy that recently moved out to the country because of my wifea€™s interested in horses.
Horse Fence Contractor for Horse Fence, Wood Horse Fence, 3 Rail Horse Fence, Electric Horse Fence and Woven Wire Horse Fence Wooden fences add beauty to a garden and are looked beyond the basic function of protection.
All Built Fence Company Affordable fence installation, construction, buider, design, repair. People have been building wood fences to mark their property and keep their horses for centuries. Call the North America One Referral Service at 1-888-258-0808 (or just dial 811) for a national directory of utility companies. Select treated lumber approved for ground contact and use weather-resistant galvanized nails and exterior screws. These fences are generally shorter, 4 feet tall or less, and don't completely block the surrounding view. This is an ideal neighborly fence style since a person on the other side will have a pleasant view of it as well.
In this case, the fence gradually steps up the slope so that each bay section is the same length and the rails are level instead of parallel to the slope. Using a trowel, slope the concrete away from the post to prevent water from collecting around it. Preassembled fence panels have a top and bottom support rail between the frame to which the pickets are attached. If your gate opening is wider than 5 feet, you should make your gate with two doors of equal width. To build a two-door gate, make frames for each of the doors, and hang them to meet in the middle.
Make the width of the gate frame 1 inch less than this measurement and the height of the frame several inches shorter than the overall height of the fence. To do this, measure the picket width and, taking the desired spacing into account, determine the number of pickets needed to cover the width of the gate frame. Make sure it clears the ground the full arc of its swing and that it clears the latched side of the post. Your finish coat will be determined by the look you want to achieve as well as the type of wood you use. Semitransparent stains are best on new wood and give an even appearance and hint of color, allowing the grain to show through. I design and build custom wood fences which reflect the architectural style of your home, whether you have a Mediterranean villa, a Spanish bungalow or a Craftsman home in the Los Angeles area. The right craftsmanship, building techniques and materials make all the difference in whether your wood fence will last 5, 10 or 15 years.
My clients also hate having construction start and stop and stretch out for weeks, so I build for one homeowner at a time and stay on your project until it is done - usually completing most projects in one to two weeks. I hope these will help you find the right builder and design a fence you will enjoy for years to come. Unfortunately, not all wood fence are built well, and it can be difficult for a layman to tell the difference between a well built fence and one that will start having problems in a few years. To achieve a whimsical style, you can make imaginative use of patterned boards, create symbols cut out in relief or apply whimsical figures onto fence board panels. You can also cut the end of fence boards into a decorative pattern to create a unique design. If your fence is intended to support plants or containers, the size and proportions should be matched to the size, weight and density of the plant. If you want to blend into the landscaping, the natural color of the wood or browns and greens work well. Common fence and privacy screen requirements include: creating visual privacy, limiting access to the property, providing security as a barrier to entry, defining a property line, enclosing a pool or play area, creating wind resistance or shade, and creating a backdrop for viewing a garden. It is also wise to verify the official property line and work out construction access and pet containment before work begins. Prevailing winds may create the need for the fencing to create an area of wind resistance or protection.


The structure should be designed to shed rain and dew readily and have good drainage away from site, leaving no standing puddles. The posts and fence boards can be made from Redwood, Mangaris™ (Red Balau), Ironwoods (Ipe) or Cedar. If it will eventually be covered with hard to remove plants, it is very important to apply multiple coatings. In Los Angeles, the popular wood (and composite) choices allow you to make tradeoffs in terms of cost, quality, color, visual appearance, ease of maintenance and the ability to resist the elements (water, sun and pests). We deliver complete fencing solutions covering all phases of construction on your farm or ranch fence project including: Used pipe is great for building strong horse panels and horse corrals. 3-rail pipe fencing for horse farms is maintenance free, great for livestock, horses, and equire ranches. This type of fence is very costly both to All Red Cedar Wood Grain Vinyl Horse Fence and Ranch Fence On Sale Now! Ia€™ve had to learn a few new things since Ia€™ve been out here Western red or Alaskan white cedar is the most cost-effective of all the wood horse fencing because it is so durable. Everyone knows the look from the miles of wooden board fence running along the Kentucky Thoroughbread farms seen in movies and Not Your Everyday White Horse Fence.
It can be custom-designed to match the style of your fence or as a focal point to the yard’s landscape. How to set fence posts in concrete, how to frame a fence, how to attache horizontal cedar fencing.
Neither the service provider nor the domain owner maintain any relationship with the advertisers. The holes are dug at least 12 inches into the ground so that the 5-foot posts become 4 foot posts when settled. Wood fences last longer if they are painted, sealing in the wood and protecting from moisture.
Make provisions for the widths of the fence panels and gates so you won't end up with odd-sized bays that can complicate installation. This allows some flexibility in layout even though you're working with preassembled fence panels.
Since this method requires that the fence be constructed to conform to the slope, it can't be accomplished using preassembled fence panels. If you want to conceal the concrete, pour it to within a few inches of the top of the hole, and cover it with soil after the concrete has set. The frame will be constructed of 2-by-4 lumber positioned on edges like the rails of the fence panels.
And I create a unique design for each client which reflects the unique look and feel of your home and garden. Good quality material and hardware, combined with superior building skills, make all the difference.
You can also create a simple fencing pattern, use stylized rail accents or post caps and accent with wooden embellishments to get an Arts & Crafts feel. For a ranch style, repeat the crossed beam (X motif) effect and accent them by painting them a contrasting color. If you want the structure to stand out or highlight nearby plants, strong colors like white or black can be used. For a long life, ivy and heavy vines should be kept off the fence with a climbing trellis mounted in front to minimize contact. Better wood grades and thicker fence boards and beams lengthen the life expectancy of your project.
These include built-ins such as benches, privacy nooks, plant containers and shelves, vine trellises, and lanterns.
In the last few years, a major change has been made to the preservatives used -- they are safer for the environment but less effective.
Based on your needs and budget, I can also build fences out of other woods and some composite materials. Any white part of a redwood board, known as sapwood, has little resistance to termites and rot.
Coast pipe has everything you'll ever need to build a quality, strong horse corral or fence.
The pipe is prepared by cutting holes to allow trapped air to escape and Visit Structural Pipe of Oklahoma, Inc., in Moore, Oklahoma, for high-quality steel pipe that can be used as fencing material, street sign poles, or building columns. This The most trusted resource for farm fence, ranch fence, livestock fence, and residential vinyl fence and vinyl fencing at wholesale, direct prices! The preservative must be properly applied to be fully Wooden board fences are the most traditional type of horse fencing.
In case of trademark issues please contact the domain owner directly (contact information can be found in whois).
The posts are spaced the appropriate distance apart, usually around 8 feet, and the three rows of rails are then nailed to the inside of the posts. Wood fences are cheaper to install and though they may not last you a lifetime, they are more natural than manmade materials--and you never have to worry about your fence cluttering a landfill one day. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Some types of preassembled panels can be cut to fit smaller bays if you end up with an odd-sized section.
If you see what you want (or something close), we can use that as a starting point for a client inspired design. Using the same color and trim details on the fence or screening as on your home will give your property a distinctive look. For the longest life, the structure should be allowed to dry out well after raining or watering plants, especially if you plan for it to support vines.
I use Construction Grade Heart Redwood, commonly known as Con Heart (see photo), which has no sapwood and some knots.
Some of the 10 footers are too rusty Wire mesh affixed to your wood rail or pipe fence is the secret to keeping critters Related Searches.
You may also find We proffesionally install Wood Horse Fences across the Carolinas since 2001! These fences are most typically made of 3 a€“ 4 horizontal planks of hardwood such as oak, 12 to 16 Ranch Driveway Gates provides Wooden Fence Gates, Farm and Ranch Gates, Estate Gates, Horse Gates and Ranch Entrances made of the strongest wood on earth. One row is generally nailed just near the top so there are only a couple inches of post above it, and the other two rows are spaced accordingly so that one row is in each third of the fence's height. This design provides greater stability than using a single 5-foot-wide gate, which might be too heavy on the hinges and can also be awkward to use. For trim, I hand select the best clear redwood (see photo) with the least amount of sapwood possible. Pressure-treated wood can be used to prolong the structure--though if you have a horse that is known to chew on wood fences, you may not want to have such chemicals in your wood fence.



Dymondwood Striker Dowels
Cedar Chair Kits
Woodworking supplies olympia wa


Comments

  1. Dr_Alban

    The ground with the construction of the walls preserve.

    07.02.2016

  2. BaLaM

    Smaller end nails and brads and How What higher idea to spend time along.

    07.02.2016

  3. sensiz_geceler

    Than one other ebook continent, nation, region, and era run out, items to analysis, or other.

    07.02.2016

  4. Blondinka

    Not solely is it a approach to spend quality.

    07.02.2016

top