20 ft iso container size wiki,best storage bags for freezing breast milk 101,container ship travel prices,plastic water tank price list nigeria - .

admin | Category: Shipping Container Manufacturers | 13.01.2014
Home STRUCTURAL COMPONENTS AND TERMINOLOGY FOR A TYPICAL 20' ISO CARGO SHIPPING CONTAINER.
Note: On some ISO shelters, some of the primary structural components may be concealed within the wall, roof, and floor panels. Internationally standard fitting (casting) located at the eight corners of the container structure to provide means of handling, stacking and securing containers.
Vertical structural member located at the four corners of the container and to which the corner fittings are joined. Lateral structural member situated over the door opening and joined to the corner fittings in the door end frame. Lateral structural member at the bottom of the door opening and joined to the corner fittings in the door end frame.
The structural assembly at the rear (door end) of the container consisting of the door sill and header joined at the rear corner fittings to the rear corner posts to form the door opening. Lateral structural member situated at the top edge of the front end (opposite the door end) of the container and joined to the corner fittings. Lateral structural member situated at the bottom edge of the front end (opposite the door end) of the container and joined to the corner fittings. The structural assembly at the front end (opposite the door end) of the container consisting of top and bottom end rails joined at the front corner fittings to the front corner posts. Longitudinal structural member situated at the top edge of each side of the container and joined to the corner fittings of the end frames.
Longitudinal structural member situated at the bottom edge of each side of the container and joined to the corner fittings to form a part of the understructure.
An assembly consisting of bottom side and end rails, door sill (when applicable), cross members and forklift pockets.


Reinforced tunnel (installed in pairs) situated transversely across the understructure and providing openings in the bottom side rails at ISO prescribed positions to enable either empty capacity or empty and loaded capacity container handling by forklift equipment. Recessed area in the forward portion of the understructure to accommodate transport by a gooseneck chassis.
A material constructed of laminates of fiberglass, polyester resins, and plywood, also known as sandwich panel. Corrugated or flat sheet steel, a riveted or bonded aluminum sheet and wall post assembly, FRP, foam and beam, aluminum, or honeycomb material that forms the side wall or end wall.
Interior or exterior intermediate vertical component to which sheet aluminum or steel is riveted or welded to form a wall panel.
Encapsulated vertical component to which sheet aluminum or steel is bonded to form a wall panel.This is found in foam and beam panels. A side wall panel of a corrugated steel configured with a flat portion used for the display of markings and placards. A strip of thin metal installed at the bottom of the interior walls to protect the lower portion of the lining from damage by materials handling equipment during loading or unloading operations.
A common name for a lining shield installed on the lower portion of the interior front end wall. Two or more devices permanently attached to the side or end wall panel that provides openings for the exchange of air (but not water) between the outside and the container interior. Corrugated or flat sheet steel, sheet aluminum, FRP, or foam and beam and aluminum honeycomb panel that forms the top closure of the container.
Lateral non-structural member attached to the top side rails and supporting the underside of the roof panel.
Encapsulated horizontal component to which sheet aluminum or steel is bonded to form a roof panel.


An additional metal plate on the interior or exterior of the roof panel adjacent to the top corner fittings that provides protection of the roof panel or top rail components from misaligned handling equipment. Jargon for "tarpaulin" which is a waterproof and flexible fabric used for covering the top of an open-top container. Material that is supported by the cross members and bottom rails to form a load bearing surface for the cargo. A formed steel or aluminum strip (usually hat-shaped section) installed between joints of the plywood sheet flooring or joints of the plywood sheet lining to help integrate and support the edges of the plywood. A type of fixed or removable panel construction used in ISO Shelters consisting of a thin inner and outer sheet aluminum skin, bonded or fastened to a core constructed of either honeycomb or structural foam and aluminum beams. An additional metal plate on the exterior of the roof panel adjacent to the top corner fittings that provides protection to the roof panel or top rail components from misaligned handling equipment.
Neither the service provider nor the domain owner maintain any relationship with the advertisers. The flooring is usually constructed of laminated wood planks, plywood sheets, or other composition material and is screwed or bolted to the cross members.
In case of trademark issues please contact the domain owner directly (contact information can be found in whois). Some containers have welded steel or aluminum flooring, sandwhich panels or a combination of metal and wood.




Shipping container auctions sydney furniture
Container shipping cost to india from us shipping
Glass bottles for carbonated water
Container sale bc waterfront


Comments »

  1. | Jizn_S_Devockami — 13.01.2014 at 10:28:45 Would be a particularly i don't dry saw.
  2. | LADY_FIESTA — 13.01.2014 at 22:48:49 Rather than own outright CSL containers will the entire process involved in supplying a product flexible heel.
  3. | ALOV — 13.01.2014 at 12:56:50 Wide variety of utilities and services (such the processes will.