How to install a hunter fan remote,tower fans online india amazon,harbor breeze handheld ceiling fan remote manual ona13av269 - Plans On 2016

Shown in Picture: (This fan is discontinued) Hunter Altitude Ceiling Fan Model 28705 in Brushed Nickel.
FREE REPLACEMENT GLASS: If you purchased your fan from us in the past 5 years (on or after March 31st 2009) and have broken your glass, we may replace it FREE OF CHARGE based on our 5 Year FREE Replacement Parts Plan.
This label is required by the FTC to be publishedby any company selling this fan on the Internet. If you cannot find what you need to make this fan work in your room, please give us a call so we can check to see if there are any further alternatives. Angled Ceilings: We do not currently have any specific information regarding an angled ceiling adapter for this fan. Building codes require ceiling fans to be installed with the blades no lower than 7 feet from the floor in residential applications (industrial fans may require more distnace). The downrod included with the Hunter Altitude ceiling fan is 3", which puts the blades 11.86" from the ceiling. This fan will hange from flat ceilings and ceilings angled up to 30 degrees using the hardware that comes in the box.
To measure the rise of your ceiling: Hold a 12" ruler ruler horizontally (using a level) with one corner touching the ceiling. The Hunter Altitude is UL Listed for Indoor use only, so it is not designed to be exposed to moisture or harsh elements.
This is rather average when it comes to ceiling fans, so you will feel some cooling breeze, but don't expect to get your socks blown off. Aside from Quality, which accounts for smooth quiet operation and durability, the amount of wind-chill a fan can provide to cool you off is the most important consideration. Use the calculator below to estimate just how much it will cost to operate this fan in "Your home". Ceiling fans cool you off by creating a wind-chill effect, so the more wind speed a fan generates, the cooler it will make you feel. Basic Help: Our operational cost calculator estimates how much it will cost to operate the Hunter Altitude ceiling fan. The wattage of the fan is already included (if it is known), but you can change it if you wish to see how the wattage affects the cost. When comparing fans of different sizes with varying CFMs, it is important to consider the wind speed in order to know which fans will make you feel cooler. Ceiling fans cool you off by creating a wind-chill effect, the degree of which is determined by the wind speed produced by the fan; the higher the wind speed, the cooler you feel.
Ceiling fan manufacturers are required by the DOE to publish the airflow of each fan in CFM (Cubic Feet per Minute) which is not the same as wind speed. The required testing method for ceiling fans is not done in a way that translates well to real world applications, so the CFM data can be somewhat deceiving if you do not know how to interpret it. The current required test procedure (shown left) shows a ceiling fan hanging above a 3 foot tall metal cylinder that is 8 inches wider than the ceiling fan (blade span) and stands 4 feet above the floor.
Therefore, the best way to compare the actual performance between fans of various sizes is to compare the wind speed. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Hunter's patented 3-position mounting system provides you maximum installation flexibility and ease. Flush Mounting (Figure 1) fits close to the ceiling, for low ceilings less than 8 feet high. Standard Mounting (Figure 2) hangs from the ceiling by a downrod (included), for ceilings 8 feet or higher. These guidelines are designed to help you select the best location for your fan and to prepare the site prior to installing the fan.
The fan blades are at least 7 feet above the floor and the ceiling is at least 8 feet high. The fan blades have no obstructions to air flow, such as walls or posts, within 30 inches of the fan blade.
The fan is directly below a joist or support brace that will hold the outlet box and the full weight of the fan.
If you plan to use an existing fan site, complete the following checklist for the support brace, ceiling hole, outlet box, and wiring.
Outlet box secured to joist or support brace by wood screws and washers through inner holes of outlet box. If your existing fan site is suitable, go to the installing the ceiling plate section and begin installing your new Hunter fan. Locate the site for the hole directly below the joist or support brace that will hold the outlet box and fan. Cut a 4" diameter hole through the drywall or plaster of the ceiling as shown in Figure 6.
Check the support brace to ensure it will support the full weight of the fan and light kit. Orient the outlet box so that both the inner and outer holes in the box align with the joist or support brace. Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off.
Thread the fan supply line through the outlet box so that the fan supply line extends at least 6" beyond the box as shown in Figure 8. Attach the fan supply line to the outlet box with an approved connector, available at any hardware store or electrical supply house. Drill two pilot holes into the wood support structure through the outermost holes on the outlet box.
Thread the lead wires from the outlet box through the hole in the middle of the ceiling plate. Align the slotted holes (refer to Figure 10) in the ceiling plate with the pilot holes in the wood support structure. For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows on the ceiling plate are pointing towards the ceiling peak.
Place a flat washer on each of the two 3" screws and pass the screws through the slotted holes in the ceiling plate as shown in Figure 11.
Remove the screw on the hanger ball to disassemble it from the downrod as shown in Figure 13. Put the set screw, previously removed, through the two black neoprene washers and the hook as shown in Figure 14.
Place the low profile washer (lip up) into the canopy as shown in Figure 15 fitting the notch in the low profile washer over the adapter set screw and hook. Rotate the canopy until the arrow on the low profile washer aligns with the tab hole on the canopy as shown in Figure 15. Align the holes in the low profile washer with the holes in the adapter and assemble securely with the three #8-32 x 1" screws. Raise the fan and place the hook through the loop on the ceiling plate as shown in Figure 16.
Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location.
Use connection 2, as described in Figure 17, if there is no separate wall switch power wire for the light fixture.


For Flush Mounting: The arrows on the low profile washer and on the ceiling plate should be pointing in the same direction and should be pointing towards the tab hole on the canopy.
Raise the canopy, be sure the holes in the canopy and the ceiling plate are aligned, and loosely assemble the canopy screws one at a time.
To remove the canopy trim ring, press firmly on opposite sides of the ring towards the canopy as shown in Figure 21. Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).
For each blade, insert one blade mounting screw through the blade iron as shown in Figure 25, and attach lightly to the fan. Align the keyhole slots in the upper switch housing with the housing assembly screws installed previously. Turn the upper switch housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots as shown in Figure 27.
CAUTION: Make sure the upper switch housing is securely attached to the switch housing mounting plate.
Remove top housing from the light fixture by loosening the three screws and turning counter clockwise. Thread the two wires from the light fixture through the center hole in the lower switch housing. Connect the white wire from the light fixture to the white wire from the lower switch housing. Install the light kit on the top housing so that the three screws are aligned with the mounting holes of the light kit. Connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. If you decide to install the fan without the light fixture please complete the following instructions.
Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze.
NOTE:Once ground wires are connected, carefully tuck wires and marrette into the metal outlet box making sure that the wires are clear of the hemisphere and downrod when positioned in mounting bracket(Downrod Mount Only). NOTE: Once wires are connected, carefully tuck wires and marrette into the metal outlet box making sure that the wires are clear of the hemisphere and downrod when positioned in mounting bracket(Downrod Mount Only).
NOTE:Should connectors on lead wires of light kit not match with connectors in the switch housing, cut connectors off and join with marrettes. Our Keystone Cougar 276RLSWE Fifth Wheel came equipped with a Coleman-Mach Analog Thermostat to control temperature when using either the Airxcel Air Conditioning or the Suburban LP Gas Furnace. I noticed a problem right away with trying to maintain a comfortable temperature in the rig. I did a little research on the web and found many people had upgraded to a digital type thermostat and were happy with the results. Mounting the unit is no problem, just take off the OEM thermostat and use the existing hole and wires. On my install I attached the gray and green wires to the outside switch toggle terminals and ran a blue wire to the fan control terminal. There are a few things to program on the Hunter 42999B Digital RV Thermostat to get things setup the way you like. I’ll add my recommendation to the others I had found; this is a great inexpensive little mod to increase your RV’s heating and cooling functionality.
Yes, the Green and Gray are the two speeds, if you only want one speed you can do away with the switch and tape off the unused wire.
Here is a pdf file I created using a LUX DMH110a non-programable digital thermostat for my Heartland North Trail travel trailer. More often than not, your going to have a ceiling light fixture at the location you are planning on installing a ceiling fan. If you are installing a fan where there is no previous fixture, then you'll be running a new circuit to the fan and can accommodate for the light as well.
Although I will be going through these circuits on this page in some detail, I recommend you checkout my other pages that cover 2-way switches and 3-way switches. Some manufacturers may use different color codes so be sure to follow the instructions that come with your particular product. This is assuming that you are installing a ceiling fan in a location that had no fixture there before. Maybe you are just replacing an old ceiling fan with a new one and you already had (2) separate switches. Pay particular attention to the "Breeze Rating" and "MPH or Wind Speed Factor" which give you the best idea of how much cooling effect you might expect from this fan.
Please call us so that we can verify that you made your purchase from us and that your glass is in fact broken (email us a picture of your fan and broken glass). If your ceiling is lower than 95.86" then you may need to add a flushmount adapter or close to ceiling dowrod if one is available for the fan (see below). The closer you are to the fan blades, the more cooling effect you will feel, so 7 feet is the optimal distance from the floor for most residential ceiling fans to get the most benefit. If your ceiling is over 30 degrees, you can by an Angled Ceiling Adapter that will allow you to install the fan on a ceiling angled up to 45. Since we already know the horizontal measurement is 12", we only need you to enter in the vertical rise to make the calculation. However, most people are used to average ceiling fans, so if you have never experienced a fan more powerful than this, you may be satisfied with the Hunter Altitude. The wind speed tells you how much breeze you can expect to feel when you are beneath the fan.
Ceiling fans can save you a lot on your energy bills if you use them properly to reduce your use of central air. The cooler your ceiling fan can make you feel, the higher you can raise your AC thermostat to conserve energy without sacrificing your level of comfort.
By default, the calculator assumes that you will leave your fan running 24 hours a day for the entire year (which is not very likely to be accurate), so you will want to change the hours and days to be more in line with how often you think you will use the fan.
If you add a light fixture to the fan, you can add the wattage of the fixture to the wattage of the fan to perform calculations with the lights on. It is more important to buy a fan with higher CFMs than it is to buy a fan that uses less electricity. The previous formula did not take into account that the testing chamber (cylinder) used to determine the CFM of a fan is 8" in diameter larger than the blade span.
CFM is the volume of air being moved every minute, whereas wind speed how fast the air is moving in MPH (Miles per Hour) or LFM (Linear Feet per Minute), both of which are directly related to the amount of wind chill effect.
The wind speed of a ceiling fan can be mathematically calculated based on the CFM and Blade Span. Even though the 52" fan moves 35% less air than the 84" fan, the intensity of the breeze that produces a wind-chill effect is over 50% more than that of the larger fan and will make you feel much cooler if you are directly beneath it. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angle mounting. Proper ceiling fan location and attachment to the building structure are essential for safety, reliable operation, maximum efficiency, and energy savings.
If you cannot check off every item, see the preparing a new fan site section for instructions on properly preparing the site for your new fan.


If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
For instructions on how to install your ceiling fan, continue with the installing the ceiling plate section.
Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate. NOTE: The rubber washers should be tight enough to keep the hook standing straight up, but the set screw should not be completely tighten as to keep the hook from being able to swing. Use the note and arrow engraved in the ceiling plate to assist in determining the direction to assemble.
The arrows on the hanger ball and on the ceiling plate should be pointing in the same direction and should be pointing towards the tab hole on the canopy. If your fan has grommets, insert them by hand into the holes on the blades as shown in Figure 22. Insert the assembly screws into the blade iron, through the blade and into the medallion, with the blade sandwiched between the blade iron and medallion as shown in Figure 24. If you want to install without the light fixture, skip to the installing without the light fixture section. Failure to properly attach and tighten all three housing assembly screws could result in the switch housing and light fixture falling. This feature gives you the option of installing the fan with or without the included light fixture. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft.
Previous purchasers and email subscribers on any of our CPO sites do not qualify for this offer. Should the following method not meet your requirements call or visit your Signature distributor for a full list of fan accessories.
It seemed like there were large swings in temperature between the furnace or the AC on and off cycles. Most of the articles recommended using the Hunter brand Model 42999B, as it was capable of controlling the cooling and heating, plus the fan function.
As far as getting your ceiling fan installed, Please follow the manufacturers manuals and safety guidelines for proper mounting due to weight and other variables which can be an important factor. If this is the case, then odds are that this old ceiling light only has enough wires to switch off & on the fan and not the light.
These pages can help you to determine how your circuits are wired or possibly help you decide how you want them wired especially if you are running a new circuit. Once verified, we will get you a replacement at no charge (just another advantage of buying your ceiling fans here at Hansen Wholesale). Due to the blade span of this fan, the actual concentration of airflow is spread over a larger area, so the ultimate cooling effect is a little less than some fans with smaller blade spans. Raising your thermostat by 10 degrees can save you up to 40% on your cooling bills, but you cannot raise your thermostat by 10 degrees if you focus only on ceiling fans that use less energy rather than ones that generate higher wind speed.
In some cases, when a light fixture of known wattage is included with the fan, the option to calculate with or without lights will show automatically.
The highest wattage consumed by the most energy guzzling ceiling fan on our website is about 120 watts.
Choosing a less powerful fan because it uses less electricity can be the worst mistake you can make because it will not cool you off enough to allow you to raise your thermostat to a high enough level without becoming uncomfortable.
When you compare two fans that are different sizes yet have the same CFM you will find they produce quite different wind speeds.
Here is a comparison where we performed the calculations between 3 fans of different blade spans and CFMs. So, to cover a larger area, two or more smaller fans with good performance may be a better choice than a single large higher CFM fan.
The steps in this guide include instructions for all three Installer's Choice mounting methods.
Making sure the light fixture mounting screw holes are aligned; hold the light fixture and tighten the nut on the inside of the lower switch housing. The inside row till contain 8 holes for 4 blades and the outside row will contain 10 holes for 5 blade use.
Although you can get just a ceiling fan most units offer a light kit that can be added in the future. Keep in mind that I refer to a load in those circuits which means a light, ceiling fan, outlet, etc..
Chances are, you only have a 3-wire cable ran to the fixture so you would be limited to powering the ceiling fan & light both. Each length will put the fan blades 7 feet from the floor, so if you want your fan blades higher than 7 feet, choose a shorter downrod to fit your needs. This is a compromise that you may be willing to accept if the actual area where you spend your time is further away from the center of the fan, which is why you may consider a larger fan such as this one. To put this in perspective: A typical central air system uses about 3500 Watts when it is running, so if a ceiling fan that uses 100 watts allows you to raise your thermostat a couple degrees higher than a more "efficient" fan that uses only 50 watts, the savings you will get by raising your AC therestat a couple degrees higher is far more than the difference of 50 watts between the two fans.
You can change this to use the average cost of electricity in your state, although this may vary widely from city to city. So if you input 120 as the fan watts and run our calculator, you will see that it still costs less than 2 cents per hour to operate the most energy guzzling ceiling fan in most states. The smaller fan must move air faster in order to move the same amount of air per minute (CFM) as the larger fan. Although this testing procedure can be valuable for comparing the performance of fans equal in size, it does not emulate a real application inside a home and does not make it easy to compare fans that are different sizes in order to determine the best size fan(s) for any particular application. Try to see what if the colors are the same on your OEM thermostat before you unhook everything.
Then leaving the double switch box is a 3-wire cable going to the ceiling fan and a 4-wire cable going to the other 3-way switch. In this case the Hunter Altitude will allow you to raise your thermostat by 1 or 2 degrees, which will still help you save additional money on your cooling bills (if you have AC).
With that said, a ceiling fan that uses less watts yet produces higher wind speed is a win-win. The airflow generated by the smaller creates more wind chill because it is more concentrated and has a higher wind speed.
I will continue doing business with them as we renovate the rest of the house.a€?a€”Shaun O. The larger fan of equal CFM moves air over a larger area so it is less concentrated at a lower wind speed. So when determining what size fan to buy you must consider the amount of space a fan will cover (the diameter of the fan plus a foot or two), the intensity of the airflow directly beneath the fan (the wind speed) balanced with how any particular size fan will look or fit in the space. Ultimately the largest fan with the highest wind speed that will look fine in the area is the best choice for performance.



Fan controller led lights 921
Hunter ceiling fan oil leak
Outdoor fans naples fl news
07.07.2013 admin



Comments to «How to install a hunter fan remote»

  1. ErroR writes:
    The fan counterclockwise for these days with your with a really massive.
  2. KOKAIN writes:
    Remain elegant, you will have to modify the parts how to install a hunter fan remote of the i do not know why state.
  3. Anastasia writes:
    Noiseless motor that operates at 320 driven ceiling fans.