Hampton bay 3 speed fan switch wiring diagram youtube,convert to flush mount ceiling fan joke,ceiling lights energy efficient ovens - Step 1

Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions. I will be running new wires to a master bedroom renovation and would like to wire the ceiling fan (a Hunter) so I can control the light and fan independently from two locations. I'll check to see if a remote module can be added to the fan, but I'm also trying to cut down on the remotes on the nightstand! For speed control, you can just substitute a 3-way speed control for one of the fan switches shown in Hammerlane's drawing. More often than not, your going to have a ceiling light fixture at the location you are planning on installing a ceiling fan.
If you are installing a fan where there is no previous fixture, then you'll be running a new circuit to the fan and can accommodate for the light as well.
Although I will be going through these circuits on this page in some detail, I recommend you checkout my other pages that cover 2-way switches and 3-way switches. Some manufacturers may use different color codes so be sure to follow the instructions that come with your particular product. This is assuming that you are installing a ceiling fan in a location that had no fixture there before. Maybe you are just replacing an old ceiling fan with a new one and you already had (2) separate switches. Even if you are experienced in working with household electricity, the disclaimer at the top of this web page contains important notes about the information in this document, so please read it if you have not already done so. This web page describes repairs made to a ceiling fan with a pull-chain speed control switch. Ceiling fans with pull chains typically include a speed control switch, a direction switch, and a capacitor. The information in this document is based on my experience fixing a ceiling fan with a 3-speed (plus off) switch and a 5-wire capacitor.
In the lower hub of the ceiling fan where the capacitor and switches are located, several wires come down from higher in the fan. The black wires on the diagram are connected to the black wire that comes down from higher in the fan.
After completing the repair, I noticed than when switching from medium speed to high speed there is sometimes a slight audible "pop" suggesting sparking inside the switch. Before disconnecting any wires, make sure you write down what the original connections are. If you do not know the pattern of the original switch and cannot find any information on it, you might consider disassembling the switch (after removing it from the fan, obviously) to see if you can determine the contact pattern. If you cannot determine the pattern of your original switch or are unsuccessful working from the original pattern, a more in-depth approach is required.
Most likely a capacitor needs to be in series between the incoming power and the motor winding.
You also need to know the internal configuration of your capacitor, since ceiling fan capacitors often contain multiple capacitors in one package. Once you know the internals of your capacitor block, you need to figure out a switch wiring that will create the desired combinations of capacitors. Note that all this experimentation with wire positions is done on paper, not with the actual wires. Twin and earth wiring is required for all installations except those using a double wall control. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. I liked that I could ask additional questions and get answered in a very short turn around. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. If you want it on a wall control, there are only a limited number of fans with that feature. As far as getting your ceiling fan installed, Please follow the manufacturers manuals and safety guidelines for proper mounting due to weight and other variables which can be an important factor. If this is the case, then odds are that this old ceiling light only has enough wires to switch off & on the fan and not the light.


These pages can help you to determine how your circuits are wired or possibly help you decide how you want them wired especially if you are running a new circuit. A common problem with these switches is that the pull chain can break off inside the switch. Unfortunately, there is no agreement among manufacturers about how to configure these components. However, I have also included some information on how to apply these concepts to the general case, so this information may be helpful even if you have a different type of capacitor or switch. A fan capacitor with more than two wires will probably contain multiple capacitors in one block.
Basically this arrangement puts the input power through a capacitor and then into one of the motor windings.
The black wire from the fan originally branched into two, but it was necessary to add a third to work with this switch.
If you know which contacts the switch connects in each speed position, then you can determine by inspection which wires get connected for each speed setting. In the case of my fan, as described in the previous paragraph, this means connecting a capacitor in series between the black and gray wires. If you do not know the internal configuration of your capacitor, you could make measurements to discover it. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. Although you can get just a ceiling fan most units offer a light kit that can be added in the future. Keep in mind that I refer to a load in those circuits which means a light, ceiling fan, outlet, etc..
Chances are, you only have a 3-wire cable ran to the fixture so you would be limited to powering the ceiling fan & light both. Unfortunately, there are many types of fan switches and it is very difficult to find the right replacement. First, increasing the capacitance in series with the coil will typically increase the fan speed. IMPORTANT: Keep in mind that this wiring is for a particular switch type and a particular fan. Then it is just a matter of finding a way to wire your new switch to replicate those connection patterns. The speed switch will also be involved of course, since it will determine which capacitor(s) are connected between the black and gray wires. Important: Remember when working with capacitors that they can store a charge even when not connected to anything.
However, please know that I cannot provide simple "this color wire goes here" responses to your questions about your particular fan. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. Then leaving the double switch box is a 3-wire cable going to the ceiling fan and a 4-wire cable going to the other 3-way switch. However, it may be possible to use a different type of replacement switch with modified wiring. The capacitors come in even more variations, including different numbers of wires, different wire colors, and different capacitance values. So, even if you are using a different type of fan, please read all the sections because they will help you understand how to figure out your particular ceiling fan.
In this regard, note that a short (direct wire, no capacitor) is like an infinite capacitor (for AC power only, not DC).
If you cannot get a replacement, or would rather just try to use whatever switch you can find at a local store, the following information may be helpful.
For example, if you know that blue and black connect to make high and orange and black connect to make medium (just for example), then you would try to find a way to wire your new switch to make those same connections when you pull the chain. Next I decided to use the 5 µF capacitor that is accessible through the green wire on the capacitor block. To check your wiring on paper, carefully trace out what the circuit will be for each switch position.
JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
The other gray capacitor wire twists together with the gray wire coming from the direction switch.


Discharge the capacitor safely and verify that it is discharged (using a volt meter perhaps) before touching the leads with your hands. Note that the two 5 µF capacitors are in parallel with each other and this combination is in series between the black wire and the motor. The red capacitor wire twists together with the red wire that comes down from higher in the ceiling fan.
Remember that the gray wires from the capacitor are connected internally to the other end of the capacitors that are on the green, brown, and red wires (see capacitor internals diagram above).
Even in a good picture it may be very difficult to read labels engraved or stamped on plastic parts.
The approach I took was to measure the capacitance between each possible pair of wires and then draw a diagram.
Also, one of the gray wires from the capacitor goes to the gray wire from the direction switch, and from there to the motor.
So, for example, it starts by connecting L and 1 on the top deck and, separately, L and 1 on the middle deck.
Then verify your design by looking at your diagram and thinking about which wires the switch will connect in each position.
What I am describing here is just the logical process I followed for determining what these wires are. So now I have 5 µF in series between black and gray when the switch is in position L-1. After discharging the capacitor, it may be wise to check with a volt meter to make sure no charge remains between any pair of leads.
On the next pull it connects 1 and 2, then 2 and 3, then 3 and L, and finally back to L and 1. The red wire from the fan was connected directly to the red wire on the capacitor, so I left it that way. I found that the black wire is apparently hot (as usual), and the white is neutral (as usual).
If you cannot find the internal configuration of your capacitor, another approach would be to consider obtaining a new capacitor whose internals you do know. I needed black to connect with this in switch position 1-2, so I added another black on contact 2 on the middle deck. On the top of the direction switch, the yellow is on the right side of the switch and the pink is on the left.
At the same time, I wanted black and brown connected on the top deck so that I would have the two capacitors in parallel. YOU MUST TURN OFF THE CIRCUIT THE FAN IS ATTACHED TO AND VERIFY THAT THE FAN IS NOT RECEIVING POWER.
In the middle of the direction switch, the white wire comes into the left side and a gray wire is on the right side. By flipping the order of the yellow and pink wires (by moving the direction switch), the rotation direction of the ceiling fan is reversed.
Since white (neutral) is on the left, the gray wire on the right seems to be the wire through which power is supplied to the motor winding. Now when the switch is in position 2-3, the black and gray wires connect on the top deck and there is no connection on the bottom deck. Note that I had to put the gray wire in contact 3 on top because even though the middle deck has black on 2 as well, it also has black on L, which would make position 3-L another high, rather than off. In my fan, it originally connected directly to the capacitor and not the speed switch, so I left this connection as it was. This is just an example of the logical approach required to develop a suitable switch wiring once you know the pattern of your switch and the internals of your capacitor.
The above information about wire colors is not intended to apply directly to any particular fan. The motor in quality fans has sealed bearings and windings with only the highest quality copper wire. The number of blades is determined more on appearance and design than air movement.Airflow is measured in cubic feet per minute, or CFM.



Buy led fans uk
Fan expo canada autograph prices
Home theater fan kit download
32 inch hugger ceiling fan with light fixture
31.08.2014 admin



Comments to «Hampton bay 3 speed fan switch wiring diagram youtube»

  1. Lovely_Boy writes:
    Energy efficiency in the workplace, then you specially compared to a industrial air.
  2. Bakinochka_fr writes:
    Home with green upgrades, and are also fairly.
  3. SINDIRELLA writes:
    May well have to adjust the bulb-holder simpler than it would with.
  4. BIZNESMEN_2323274 writes:
    Lighted decorations for your residence or organizations holiday.