Plans For Making A Corner Desk,Diy Playhouse With Pallets,Plans For Carport - You Shoud Know

22.08.2015
The main weakness of this design is that the MDF is not very strong material and this desk will probably only last about 5 years in normal service.
This design includes nine detailed sketches that are critical to your successfully building this desk. This sketch shows the Long Bottom Assembly that is one of three assemblies that support the desk top. This sketch shows you how to cut the first sheet of 0.5" MDF to make the two desk tops and parts of the base. This sketch shows the layout of the pieces for the upper book shelf on a 48"x48" piece of 0.75" MDF.
This desk was designed so that it could be built by an amateur woodworker using tools commonly used for home fix up.
Go over all the computer and audio equipment you wish to support with this desk and determine the size for each piece. Air Typing is an exercise given on our Web Site to help you determine the height you need for the keyboard, the monitor, and the angle for the monitor. Fit, glue, and clamp the strips to the underside of both desk top pieces as shown in Sketch #3.
Do not install the MDF pads for the screw blocks that hold the top down or cut the cable holes at this time. Decide on locations for nine 5" pieces of 1.5" stock to accept the screw blocks that hold on the top.
Detailed cabling instructions and plans for a remote power switch are given in our Web page under Freebies. If you send us a picture of your finished desk, we would be happy to put it on our web page.


This sketch shows the Long Bottom Assembly that is one of two assemblies that support the desk top. This sketch shows you how to cut the first sheet of 0.75" MDF to make the two desk tops and parts of the base.
The Simple Corner Desk in 0.5" MDF has an upper bookshelf that you can add to this one if you like. They are used to tie the top to the base assemblies and can only be screwed to places where the MDF is double thickness. Drill pilot holes, screw, and glue them to the bottom assemble pieces but do not glue them to the desk top. I recommend: thinned shellack on everything, a dull color of paint for the bottom, bright paint for the top, and two coats of satin finish polyurethane on everything. You think about brick red for the base and top book shelf, and Chinese Red for the desk tops. Apply two coats of satin finish polyurethane to all surfaces except the bottom of the desk tops. Basically I have a cabinet at each end with cleats running along the wall for the open portion. This version is smaller and lighter, it has a upper bookcase, and was designed for use with a wheel chair.
You may wish to have only one keyboard tray and reduce the height of the desk by about 2 inches. The design includes two small book shelves below the desk top and a larger shelf unit on top. Cut the 2"x4" bolt blocks, drill for the bolts, and glue them to the sides of this assembly.


If you know the location of the AC wall outlet that will be used with this desk you can cut a large access hole for it. For the front, one 2x2 goes from wall to wall [also mounted to the top of the cabinet] and the other from the other cabinet until it intersects with the other 2x2. If you know where the electrical outlet will be on the wall, you can cut a large hole for the AC plugs. The MDF blocks and cable holes shown will be located when the base is complete and sitting upside down on the desk tops. If you know the location of the wall AC outlet you will be using you can cut a larger access hole for the plugs.
I do not believe to need the front legs and could just attach the corner top to the side cabinets.
The top attachment screw blocks and cable holes shown will be located when the base is complete and sitting upside down on the desk tops.
You can use #4 finishing nails in the 0.75" MDF if you redrill a hole using a nail with the head cut off for a drill bit. I am also particularly worried about the support for the corner portion so any thoughts on that would be appreciated.



Plywood Sheets For Flooring
Rojek Woodworking Machinery Ireland
How To Build An Outdoor Corner Bench With Storage
Portable Thickness Planer Reviews 2015

Category: Equipment Shed



Comments to «Plans For Making A Corner Desk»

  1. oskar writes:
    Own behalf for an answer to foreclosure and who will take any.
  2. BAKILI_BMV writes:
    Out on the plans in order that when.
  3. Gulesci_H writes:
    Sentence the usage of wood for making such for wooden clarinets classic.