25 May. 1984|
Water based wood stain colours,ercol dining table second hand,applying paper backed wood veneer - Reviews
We all know of the traditional colours of wood stain, where your finished product, whether that be a deck, an exterior door, or interior surfaces, become a shade of cherry, mahogany or deep brown. Now these colours will be dependent upon what type of wood you have, whether it is treated, and whether it has been stained before or not. If you’re looking to get colours such as: Cinnamon, Onyx, Fruit Punch, Winter Moss, Spice, Burgundy, Deep Ocean, Island Water, and so on, then you’ll be looking at getting a water based stain that is made with a colour tint. If you’re looking for lighter colours than the ones above then you’re going to want to go with a water based stain that has a white tint to it. If you are looking for regular colours of browns and reds than you can look to buy either oil based, varnish or other types of stain. This water based wood stain is designed to colour the wood, it then requires a top coat of oil, lacquer or wax to finish the job. These wood stains are made from the finest natural ingredients from around the world, to give quality colour pigement to the stains.
The hard and soft grain form the pattern in soft woods and pine, the soft grain makes up the majority of the wood content. The depth of the colour can be increased by applying 2 to 3 coats of water based wood stain. If marks on the wood are left after the water based staining application, these tend to be blemishes in the wood that can not be covered by water based wood stain.
New or old furniture, floorboards or any wooden surfaces can be treated with this interior water based wood stain.
Our wood stain colour collection can transform the look and feel of any room by treating or refurbishing the furniture or floorboards.
Foam Sponge: Large surface areas can be wiped over with a sponge easily, when more pressure is applied to the sponge more stain is released to cover the area being treated to save time replenishing the sponge. When using a brush to apply the chosen top coat to the water based stain (such as water lacquer), ensure to keep the brush strokes to a minimum so not to lift the colour out of the stained wood.
Approx 10 square metres per litre, this can be dependent on the amount applied, the wood and temperature.
A thin coat being 2 hours, 4 hours for a thick coat, this also fluctuates with temperature and the wood being used.
This is the main define statement for the page for english when no template defined file exists. I think a lot of us know that there are different colours of stains that can be applied to wood but never think about them as we only ever recognize the typical types that we see. You can obtain some pretty wacky colours if you use certain stains, as there are seven different types of stain available to buy.
Lower quality stains create a reverse negative effect that can be magnified once the top coat has been applied to give a bad finish. Pay particular care and attention to the cut ends of the wood areas, these area tend to absorb more creating tide marks on the surface of the timber.
You can also personalise your wood stain colour by adding other red, yellow, orange or brown wood stain or concentrated dyes.
This gives you good working time with the stain, so you can tidy up runs and excess areas to give you a nice even finish once dried.
Once an even application has been applied, the surface can wiped over with an absorbent cloth or sponge to remove excess stain. The most common is oil stain, then varnish, water based, gel, lacquer, water-soluble dyes, and metalized dye stains. This is opposed to lesser quality pigments that leave the wood with a washed out zebra effect finish. This can create hundreds of colour variations by inter mixing our products to give you desired shade or perfect match.
This effect will give it a rustic appearnace, if that is the desired effect, you can enhance the high and lows of the rustic colouring by brushing on a dark wax to the raised wood grain. Once dried the water based stains can be coated with most varnishes (lacquers), waxes and oils to give a final finish. Now a lot of these stains will work better with some types of wood and not others, so reading the can of stain before buying is a must.