Gl gg zekering engels,www.gc hechingen,renal function in type 2 diabetes with rosiglitazone metformin and glyburide monotherapy,pictures of diabetic bodybuilders 2014 - Plans Download

A device that by the fusing (melting) of one or more of its specially designed and proportioned components, opens the circuit in which it is inserted by breaking the current when this exceeds a given value for a sufficient time. In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a "sacrificial" device to provide overcurrent protection, of either the load or source circuit. A fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented.
A fuse consists of a metal strip or wire fuse element, of small cross-section compared to the circuit conductors, mounted between a pair of electrical terminals, and (usually) enclosed by a non-combustible housing. The fuse element is made of zinc, copper, silver, aluminum, or alloys to provide stable and predictable characteristics.
The fuse element may be surrounded by air, or by materials intended to speed the quenching of the arc. Fuses can be built with different sized enclosures to prevent interchange of different ratings or types of fuse. Indicating disc — a coloured disc (flush mounted in the end cap of the fuse) falls out when the element is blown.
Element window — a small window built into the fuse body to provide visual indication of a blown element. External trip indicator — similar function to striker pin, but can be externally attached (using clips) to a compatible fuse.
Some fuses allow a special purpose micro switch or relay unit to be fixed to the fuse body.
Some fuses for medium-voltage applications use two separate barrels and two fuse elements in parallel. The speed at which a fuse blows depends on how much current flows through it and the material of which the fuse is made. Two broad fuse characteristic types are (1) dual-element, time-delay fuses and (2) non-time delay fuses. The graph shows the difference between the melting curves of a typical 100 ampere dual-element time delay fuse and a non-time delay fuse.
Voltage rating of the fuse must be greater than or equal to what would become the open circuit voltage. Medium-voltage fuses rated for a few thousand volts are never used on low voltage circuits, because of their cost and because they cannot properly clear the circuit when operating at very low voltages. Similar appearing fuses may have significantly different properties, identified by their markings. The International Electrotechnical Commission publishes standard 60269 for low-voltage power fuses. In the United States and Canada, low-voltage fuses to 1 kV AC rating are made in accordance with Underwriters Laboratories standard UL 248 or the harmonized Canadian Standards Association standard C22.2 No. LV HRC fuses are used for installation systems in non-residential, commercial and industrial buildings, as well as in the switchboards of power supply companies.
All fuses used on power systems from 1.5 kV up to 138 kV are categorized as high voltage fuses.
Large power fuses use fusible elements made of silver, copper or tin to provide stable and predictable performance. So-called self-resetting fuses use a thermoplastic conductive element known as a Polymeric Positive Temperature Coefficient (or PPTC) thermistor that impedes the circuit during an overcurrent condition (by increasing device resistance). A thermal fuse is often found in consumer equipment such as coffee makers or hair dryers or transformers powering small consumer electronics devices.
Its essential component is a metal wire or strip that melts when too much current flows, which interrupts the circuit in which it is connected. The fuse is arranged in series to carry all the current passing through the protected circuit. The fuse ideally would carry its rated current indefinitely, and melt quickly on a small excess.
When the fuse element blows, the indicating pin extends to activate the micro switch or relay, which, in turn, triggers an event. Semiconductor devices may use a fast or ultrafast fuse as semiconductor devices heat rapidly when excess current flows. If we look at a comparison at 500 amperes, the dual-element fuse melts in about 10 seconds and the non-time delay fuse melts in .2 seconds. This term is normally used in short circuit conditions and the values are used to perform co-ordination studies in electrical networks.


For example, a glass tube fuse rated at 32 volts would not reliably interrupt current from a voltage source of 120 or 230 V. Resistance may change when a fuse becomes hot due to energy dissipation while conducting higher currents. Surface-mount technology "chip type" fuses feature few or no markings, making identification very difficult. The standard is in four volumes, which describe general requirements, fuses for industrial and commercial applications, fuses for residential applications, and fuses to protect semiconductor devices. High voltage fuses are used to protect instrument transformers used for electricity metering, or for small power transformers where the expense of a circuit breaker is not warranted.
High voltage expulsion fuses surround the fusible link with gas-evolving substances, such as boric acid. The PPTC thermistor is self-resetting in that when current is removed, the device will cool and revert back to low resistance. They contain a fusible, temperature-sensitive alloy which holds a spring contact mechanism normally closed.
Short circuit, overloading, mismatched loads or device failure are the prime reasons for excessive current.
Overcurrent protection devices are essential in electrical systems to limit threats to human life and property damage. The element must not be damaged by minor harmless surges of current, and must not oxidize or change its behavior after possibly years of service. A dual-element fuse may contain a metal strip that melts instantly on a short-circuit, and also contain a low-melting solder joint that responds to long-term overload of low values compared to a short-circuit. Automotive glass fuses were made in different lengths, to prevent high-rated fuses being installed in a circuit intended for a lower rating. Fuses have different characteristics of operating time compared to current, characterized as fast-blow, slow-blow, or time-delay, according to time required to respond to an overcurrent condition. The fastest blowing fuses are designed for the most sensitive electrical equipment, where even a short exposure to an overload current could be very damaging.
The dual-element, time-delay fuses are widely used in general purpose applications, motor circuits, transformers, and other circuits. This resulting voltage drop should be taken into account, particularly when using a fuse in low-voltage applications. Operating values will vary with each fuse family and are provided in manufacturer data sheets. The IEC standard unifies several national standards, thereby improving the interchangeability of fuses in international trade. This standard applies to fuses rated 1 kV or less, AC or DC, and with breaking capacity up to 200 kA. In North American standards, the fuse is the replaceable portion of the assembly, and a fuse link would be a bare metal element for installation in a fuse. For example, in distribution systems, a power fuse may be used to protect a transformer serving 1–3 houses. When the fuse blows, heat from the arc causes the boric acid to evolve large volumes of gases.
The most frequent application is in transformer circuits, with further uses in motor circuits and capacitor banks.
When the surrounding temperature gets too high, the alloy melts and allows the spring contact mechanism to break the circuit. Fuses are selected to allow passage of normal current plus a marginal percentage and to allow excessive current only for short periods. The size and construction of the element is determined so that the heat produced for a normal current does not cause the element to attain a high temperature. Fuse elements may be supported by steel or nichrome wires, so that no strain is placed on the element, but a spring may be included to increase the speed of parting of the element fragments.
A standard fuse may require twice its rated current to open in one second, a fast-blow fuse may require twice its rated current to blow in 0.1 seconds, and a slow-blow fuse may require twice its rated current for tens of seconds to blow. An overload current condition may only be temporary in nature, and the current may subside to normal current conditions in short order.
The non-time delay current-limiting fuses are used where fast response with little or no overload delay is desired. For coordination of fuse operation with upstream or downstream devices, both melting I2t and clearing I2t are specified.


Some fuses are designated High Rupture Capacity (HRC) and are usually filled with sand or a similar material.
Plasma inside that glass tube fuse may continue to conduct current until current eventually so diminishes that plasma reverts to an insulating gas. Voltage drop often is not significant in more traditional wire type fuses, but can be significant in other technologies such as resettable fuse (PPTC) type fuses.
All fuses of different technologies tested to meet IEC standards will have similar time-current characteristics, which simplifies design and maintenance.
These fuses are intended for installations following Canadian Electrical Code, Part I (CEC), or the National Electrical Code, NFPA 70 (NEC). A circuit breaker at 115 kV may cost up to five times as much as a set of power fuses, so the resulting saving can be tens of thousands of dollars. The associated high pressure (often greater than 100 atmospheres) and cooling gases rapidly quench the resulting arc.
These type of fuses may have an impact pin to operate a switch mechanism, so that all three phases are interrupted if any one fuse blows. Slow blow fuses are designed to allow higher currents for a modest amount of time longer, and such considerations are and were commonly necessary when electronics devices or systems had electronic tube tech or a large number of incandescent lights were being powered such as in a large hall, theater or stadium.
If too high current flows, the element rises to a higher temperature and either directly melts, or else melts a soldered joint within the fuse, opening the circuit. The time delay fuse (also known as anti-surge, or slow-blow) are designed to allow a current which is above the rated value of the fuse to flow for a short period of time without the fuse blowing.
For example, a typical harmless current overload is encountered whenever most motors are started.
A typical application of these is for protecting circuit breakers for possible large short-circuit current levels.
The melting I2t, is proportional to the amount of energy required to begin melting the fuse element. Fuses for small, low-voltage, usually residential, wiring systems are commonly rated, in North American practice, to interrupt 10,000 amperes. Rated voltage should be larger than the maximum voltage source it would have to disconnect. Pole-mounted distribution transformers are nearly always protected by a fusible cutout, which can have the fuse element replaced using live-line maintenance tools. Thermal fuses are a 'one shot', non-resettable device which must be replaced once they have been activated (blown).
Tubes and incandescent lights each have reduced current needs as they heat up to operating temperatures for their internal resistance grows as they are heated— the same physics principle causes the fuse material to melt, disconnecting the circuit from power. These types of fuse are used on equipment such as motors, which can draw larger than normal currents for up to several seconds while coming up to speed. The built-in fuse time delay permits the motor to start without unnecessarily blowing fuses. The clearing I2t is proportional to the total energy let through by the fuse when clearing a fault.
Fuses for larger power systems must have higher interrupting ratings, with some low-voltage current-limiting high interrupting fuses rated for 300,000 amperes. Rated voltage remains same for any one fuse, even when similar fuses are connected in series.
The energy is mainly dependent on current and time for fuses as well as the available fault level and system voltage. Fuses for high-voltage equipment, up to 115,000 volts, are rated by the total apparent power (megavolt-amperes, MVA) of the fault level on the circuit. Connecting fuses in series does not increase the rated voltage of the combination (nor of any one fuse).
Since the I2t rating of the fuse is proportional to the energy it lets through, it is a measure of the thermal damage and magnetic forces that will be produced by a fault.



Gl_lines adjacency ext
Gastric bypass cures type 2 diabetes yahoo


Comments

  1. FASHION_GIRL

    Which meant I have been having to revise.

    24.03.2015

  2. Natalyu

    Consuming plenty of excessive-sodium meals like cheeses and olives this.

    24.03.2015

  3. OKUW

    Cisplatin, phenytoin and the class fat and to favor low-glycemic index foods things such as working.

    24.03.2015

  4. SEXPOTOLOG

    The past been linked with diabetes, neglecting the sustainable low carb.

    24.03.2015