Wood veneer repair cost, small shank router bits - Try Out

Categories: Woodworking Shelf Plans | Author: admin 05.03.2012

Gerry and I recently returned from a trip to the Big Island of Hawaii, where we first learned of the Koa tree, and immediately fell in love with the wood.
Around the 1970′s furniture makers began using thinner veneers on particle board, medium density fibre boards (MDF) and plywood cores. In our experience, veneer over solid wood is easier to repair, because wood can be patched and even glued back into shape. Yes, it does matter what’s underneath the veneer, especially if it is damaged and needs to be repaired. Veneer has gotten a bad reputation over the years (and some for good reason.) Many people think of wood veneer as inferior and cheap. Veneer is a thin layer of wood that is cut or peeled from a log, then bonded onto other surfaces to create a visually pleasing pattern. On older and finer pieces of furniture, the veneer is glued onto pieces of other wooden boards. During the 19th and early 20th centuries, furniture makers began using veneers to make the more beautiful and valuable pieces of wood go farther. Around World War II, fine wood became scarce and lesser wood veneers were used to create quality, affordable furniture. It is very difficult to determine the thickness of the veneer unless there is some sort of blemish or the veneer has chipped off.
This early 20th century drawer was inlaid with 2 different veneers to create a beautiful design. The veneer on this newer table was beautiful, but it was so thin, it was difficult to sand when the customer wanted it refinished. A friend of mine recently purchased a dining table from a high end furniture store, after being told by the salesperson that it was solid wood.  While it is true that the table was made mostly from wood products, it was not solid wood. The salesperson might have thought the table she sold my friend was solid wood because it was so well made, and the particle board cores were covered with beautiful wood veneer. Please refer to Part 2 in this series about wood, wood products & veneers for more information about veneer and the history of veneer. What I love most about my job is seeing the smiles on the faces of customers when they see their furniture after it has been refinished or repaired. Because a veneer layer is so thin and the wood underneath it is often a porous type of wood, such as particle board, veneer can blister. In order to replace veneer outright, decide upon which type of veneer is necessary for the project. When a section of veneer is securely in place and not in need of further repair, be sure to finish the job by cleaning and polishing the piece.
While not everyone is an expert at furniture repair, even a novice can fix most issues with wood veneer.


Some of the benefits of using particle board, MDF and plywood are that it is cheaper, saves trees, and does not warp like solid wood can. Even high end plywoods can be repaired in most cases because it is made with several layers of wood and glue. If a part of the piece is crushed, dented or broken, it cannot just be glued back into place like wood can.
Some think it’s only on new furniture, and is not really wood, but a manmade product. It is usually the finest grain of wood from a tree, with the most interesting grain or pattern.
Today, some veneers are as thin as a piece of paper, making them difficult to repair if damaged.
Beautiful veneers of mahogany, walnut, or quarter-sawn oak were often glued to birch or regular cut oak.
Around the 1970′s, manufacturers began using thinner veneers and adhering them to plywood, particle boards, and medium density fibre boards. I am not going to say that she was purposely misled or lied to, because most furniture store workers are salespeople and not wood experts.
However when the painters removed the tape they used in the kitchen, pieces of the wood veneer came off the particle board cabinet siding. This means that rather than solid wood, a thin layer of decorative wood sits atop the solid piece. It is quite common for veneer on old furniture to blister, particularly if stored in a humid environment. This happens when the wood under the veneer absorbs moisture from the surrounding environment and pushes the veneer up and creates a bubble on the surface. If a section of veneer is peeling up at the corner, but is otherwise intact, this is an easy fix.
This type of project is a much bigger undertaking since it is necessary to remove all the old veneer, as well as the dried adhesive, and then sand the surface until smooth.
However, installing fresh veneer can breathe new life into a piece that would otherwise end up discarded.
Whether you are replacing damaged veneer or building your own piece, be sure to search eBay for deals on furniture and supplies. We never actually saw a tree because we basically stayed at sea level (hey, it’s Hawaii with an ocean and sandy beaches, and we live in Arizona!) but we did visit several galleries and even a lumber yard to purchase a block of wood for a wood-turning friend. But veneer has been around for a long time, and historically has been used on the finest furniture.
During the Renaissance era, tiny pieces of exotic wood were used for marquetry on the finest pieces of furniture.


The lack of good quality craftsmanship and inferior adhesives since then has resulted in veneers getting a bad reputation.
Table and chair legs are often made of solid wood, although less expensive ones are made of particle board and covered with veneer.
If the grain from the top surface is not the same on the underside, it is most likely not solid wood. If there is a seam or a band where the grain does not continue over the edge, then it is most likely veneer.
Since veneer is usually rolled from a tree, the width of the veneer can be much wider than a wooden plank.
Veneers are common because they are a cost effective way to make furnishings more aesthetically appealing. If it is possible to find a piece of veneer from another part of the furniture that is not visible, attach that chip to the broken spot with an appropriate adhesive. Throughout the 18th and 19th centuries, the finest furniture makers used exotic wood veneers to create beautiful and intricate patterns on their finer pieces. That being said, there are still some fine furniture makers today who make quality furniture with thicker veneers bonded to wooden surfaces. When it does, place a weight on top of the cardboard and leave it overnight, allowing the veneer to cool flat.
But what is so beautiful is the wood itself; it can have a variety of grain, ranging from plain to curly to fiddlestick.
Solid wood can sometimes warp, shrink or expand depending on humidity, causing veneer to crack. In those days, veneers were used as a piece of art and you will find many of these pieces of furniture in museums.
Antique wood furniture may be in sound structural shape but cracks and blisters in the veneer make the pieces unattractive.
Follow the package instructions on either wood glue or contact cement and adhere the veneer back to the surface of the piece. Thankfully, it is possible to repair wood veneer with the proper tools and a little patience. Using simple wood veneer repair techniques can turn even old, discarded furniture into cherished pieces of decor.




Outdoor playground equipment plans
Dark wood low tv stand
Finland plywood manufacturers
House plans covered patio
Ceramic sandpaper


Comments: