Through dovetail joints, sandbox with lid plans - Review

Categories: Work Bench Plans For Garage | Author: admin 04.10.2011

The joint ought to go together by light driving, and be perfectly square on the indide between the working faces. Dovetails are also the best joint for building solid-wood boxes, like this chest of drawers. Traditional drawers have half-blind dovetails at the front, and through-dovetails at the back.
The traditional way to cut dovetails is by hand, using a saw and chisels, and that yields the prettiest joint with very narrow pins.
A good dovetail jig will cost you $100 or more, and you’ll need a router, too, but it makes short work of these fancy joints. For a beginner, one of the most daunting aspects of building a piece of furniture is deciding what joints to use.
If you were building a cabinet or sideboard with a face frame that intersects at various points, you might use a half-lap joint. Tongue-and-groove joints provide a mechanical means of registering and joining the edges of narrow boards when forming a wider panel. The finger joint, sometimes called a box joint, interlocks two boards at a corner similar to a dovetail. Considered one of the strongest and certainly the most beautiful of joints, the dovetail exacts a stiff price in terms of skill for the strength and good looks it provides. This joint consists of a dovetail-shaped tenon that slides into a corresponding groove or plow. Show off the joint if it's appropriate--Nothing looks better than eye-popping dovetails or a tight, pinned mortise-and-tenon. There is simply no stronger or prettier way to join the sides of a solid-wood box, whether it is for a big chest or one of the drawers inside it, which might be pulled in and out thousands of times in its life.


The tails look like the tails of doves (hence the name), and the pins are on the opposite board and fit in between the tails to create a joint that is impossible to pull apart in at least one direction.
Choosing the wrong joint can complicate construction, conflict with the design, undermine its integrity, and maybe even cause premature failure of a piece.
On this joint you remove the full width of each intersecting member but only half of the thickness. This joint can be used to join the rails and stiles on frame-and-panel doors, the aprons to the legs of tables, and the rails to the posts or legs of chairs. The joint must allow for additional operations, such as grooving, rabbeting, moldings, or screws. Note how the angled surfaces interlock, and how the joint begins and ends with a half-pin at the top and bottom. Add some glue, clamp the joint together well, and it will be impossible to pull apart in the other direction, too. A good place to begin when faced with the task of choosing a joint for a certain application is to identify and study the most widely used joints; there literally are hundreds of them in various configurations.
The strength of this joint relies on the straightness of the edges (not necessarily the squareness). Several half-lap joints on a cabinet face frame will ensure that it is rigid and long-lasting.
This joint has a clean, utilitarian look that makes it perfect for kitchen, office, or shop containers. The first hurdle is to cut each half of the joint to 45 degrees; then you have to figure out a way to glue them together without one half slipping past the other.
If you were building a Shaker candle stand, the sliding dovetail would be the strongest way to attach the legs to the column.


Crowding the joint with pins can leave too little material on the tail board to support the joint. A vertical cut is made as at a, using the mallet, then one at b; these to be repeated until one half through the piece, then cut on the opposite side. You’ll also need a pricey jig to make nice dovetails, while hand tools are cheaper, and can be used for many more tasks.
Then consider the joints traditionally used in a particular type of furniture and evaluate your ability to execute them.
Half-blind dovetails are most commonly used to join drawer sides to drawer fronts, but occasionally you'll find the joint employed in the construction of carcases. Disadvantages are that the joint is visible from the end of the panel and the joint requires precise milling to ensure that all parts fit correctly. The tenon can be stopped or continue through a board, and it can be reinforced with pins or wedges.
Today, there are jigs that enable a woodworker to cut dovetails by machine, but the end result looks mass-produced.
Bring the edge of the blade of the try square to coincide with the lines b and c on the end of the mortise piece, and mark with the knife a line joining them.
In this article I highlight some of the most standard joints and their common applications.



Pool table furniture plans
Router duplicator
Woodworking courses london ontario
Platform bed with drawers design plans
Plans to build a television stand


Comments: