How to build wooden gates and picket fences, dual monitor computer desk with hutch - PDF Review

Categories: Wood Wine Rack Plans | Author: admin 23.11.2014

Wood fences: Each of our wood fences are engineered with pressure-treated wooden posts, so you can feel certain they are ready for ground contact prior to entering the ground. Wood gates: Our Jacksonville, NC wood gates and wooden gate systems are also designed to protect our customers against expansion, contraction and warping.
Picket fencing: In addition to our standard wooden gates and fences, Seegars offers its residential and commercial customers a variety of picket fencing and post cap design options. If you are looking for a wood fence that both protects and complements your yard, look no further than SeegarsĀ® Fence Company. To get started today on your wooden fencing project, contact the customer service representatives at SeegarsĀ® Georgetown Road office by phone at (910) 346-1121. We'll begin by cutting the two ledges; these are the two horizontal rails that the front uprights, or pickets, will be fixed to. For the size of gate I'm going to make, we're going to need 7 of these, so first, cut these square to 36 inches (915mm) long.
If you're using a mitre saw for this, it's simply a case of setting the saw to 45 degrees and then setting a stop on the saw to the required length; you can make a quick stop using a G-Cramp and a scrap of timber in seconds.
To start, we're just going to fix the end two pickets to the ledges, rather than go flat out and fix every one of them. The positions of the rails in the gate I'm making are; 6" or 150mm from the BOTTOM of the gate to the UNDERSIDE of the bottom rail and again 6" or 150mm from the TOP of the pointed pickets to the TOP of the top rail. Starting with the bottom ledge, position the picket so it is flush with the end of the ledge and the line you've just marked meets up with underside of the ledge.


This is where it will be fixed; pre-drill two screw holes, remove the ledge and apply glue.
Move up to the top ledge and repeat the process, this time keeping the line on the picket to the top of the top ledge.
To do this, place all the pickets onto the ledge and push them tightly to one side of the gate; they want to be hard up to one of the first pickets we fixed.
Now measure the distance between the edge of the last loose picket and the picket that is fixed to the gate, on the opposite side of the gate to where the pickets are. What you'll need to do now is to cut a couple of pieces of timber to 47mm wide to use as spacers - if you're using more or less uprights, then the measurement of 46mm wide bears no relation to your gate; you will need to work the measurements out as I've done above and use these measurements instead - the number of gaps is always one more than the number of loose pickets. This temporary timber will just enable us to line all the remaining pickets to the bottom of the gate. Starting from one end of the gate, place the lose packers between the fixed picket and the still loose picket (sit the packers on the ledges), slide the picket down so it touches the temporary piece of timber that we've attached to the bottom of the gate.
Lie the gate so the back is facing up and lie the diagonal brace in position; do a quick check with a combination square if you have one, just to make sure it's sitting around 45 degrees. Replace the brace and pre-drill 2-3 screw holes in total along the length of the brace, through the brace into the pickets; securely screw this together and that's it, apart from cleaning up any glue that's leaked out.
So you place it, then make sure its not less than 45 degrees before marking cutting and fitting.
At SeegarsĀ® Fence Company, you can have your cake and eat it too with classic wood fencing that is guaranteed to withstand the test of time.


We utilize only the best wood fencing materials and latest fencing installation technologies, so you can spend less time worrying about potential water damage and more time enjoying the beauty and comfort offered through your new wooden fencing! Constructed with a welded galvanized steel frame and powder coat finish, our wooden gate systems are built to last a lifetime. Our Jacksonville, NC fencing experts are dedicated to helping you create the wooden fence or gate of your dreams through our esteemed fence design and installation services. Gate-wise, unless you include hanging a sheet of plywood as a gate, this is the simplest gate you could possibly make as it’s just a legged and braced gate – there are no awkward joints to cut!
You can either make use of a mitre saw, if you're lucky enough to have one, or just go old school and use a handsaw.
It can be less than 45 degrees, but no flatter than 45 degrees as it won't be doing anything to support the gate. Mark the position on all the pickets that it crosses (on both sides of the brace) and then remove the brace and apply glue between the lines you've just marked. Whether you are interested in residential and commercial fencing, you can feel confident knowing that you are getting the greatest return on investment with our Jacksonville, NC wooden gates and fences.



Woodworking sanders
Royal custom designs furniture
Building gun cabinet plans


Comments: