When looking for a good miter saw, then why not check out the Ryobi ZRTS1342L 10-Inch Compound Miter Saw. No longer do you have to deal with callouses from hand held saws and back aches from heavier miter saws. The 14amp and 5,501rpm motor of the Ryobi ZRTS1342L 10-Inch Compound Miter Saw gives it enough horse power to cut through most common materials such as wood and soft plastics. The dust bag of the device catches sawdust before the dirt hits the ground, allowing for a more mess-free process. One thing that users will most likely enjoy about this device is its laser light guiding system, which allows individuals to make straighter and more accurate cuts.
The dust bag, which nearly all miter saws come equipped with, is good at catching any debris that will fall from your materials. The price of this unit is more inexpensive than most miter saws as well, which people will undoubtedly enjoy.
Some customers have commented on how it has been difficult to keep a 90 degree angle fixed. Majority of users who have reviewed this device are more than satisfied with the quality brought to them by the Ryobi ZRTS1342L 10-Inch Compound Miter Saw. Overall, if the fact that this device is factory reconditioned does not bother you, then the Ryobi ZRTS1342L 10-Inch Compound Miter Saw is an inexpensive and practical buy for users look for a well-functioning miter saw.
If you found this review useful then read the full review for the SKIL 3820-02 120-Volt 12-Inch Compound Miter Saw. This entry was posted in 10 Inch Miter Saw, Ryobi Miter Saw and tagged Ryobi ZRTS1342L, Ryobi ZRTS1342L 10-Inch Compound Miter Saw by Mike. Ryobi makes a somewhat more expensive version of this saw that, I believe, comes with a laser guide, but other than that I cannot see a big advantage to the more upscale version – at least for those on a budget. OK, $99 is cheap for a miter saw, and I would be remiss if I said that this was a superior saw that will work wonders for any serious woodworker. I asked him about it and he said that one simply could not lose with a saw that cost only a buck less than a C-note. I probably should have let him write this review, but a secondary source is better than nothing, and, besides, I have also used mine for some on-site work and it did fine for me. Ten years is plenty for me, since I do not run my gear enough to put serious wear and tear on the stuff, anyway.


I did purchase spare brushes for the motors (the brushes for most of the Ryobi and Ridgid induction motors in the 14-15 amp range are the same), and I have also purchased spare drive belts here and there for my Ryobi, Ridgid, Delta, GMC, and Craftsman tools, hand type and stationary type. Good reviewThis is a saw many people own a number of my students own it and it’s far better than a circular saw and is not made for production work. DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. This was one of the two tools I received for x-mas that got me started (the other was a Ryobi 1.5HP router). As for cons, I would add that the fence isn’t great, though it does include holes to attach a higher auxiliary fence. The best way to keep the dust out of your workshop when using a miter saw is to take the saw outside. The unit’s work clamp holds piece in place, to minimize errors that might occur due to accidentally moving the piece while sawing. The laser guide quickly marks the place where the cut is to be made enabling you to make precise cuts. Some time back the wife and I were having a major-grade addition attached to our house and one of the super carpenters on the job (there is always a super carpenter or two on projects like this, and thank God for that) had one of the things in addition to the big DeWalt unit he kept stashed in his truck. He said he could lob it into the back of the truck, leave it out in the rain, and never worry about somebody in the area stealing it when it was left unattended. It might be wise to purchase an extra saw guard and some other basic parts while the saw is still current. I suppose this is one advantage to having lots of gear, with duplicate capabilities from various items.
I have spare brushes for some of the non Ryobi and non Ridgid tools, too, of course, as well as spare tires for my two band saws. When a new model is built the car manufacturing people calculate how long various parts will approximately last and then build enough spares at that time to last just long enough. This is an important safety feature of the machine, allowing users to have a safe sawing experience. It can bevel in one direction out to 45 degrees and the motor is a decently powerful 14-amp job. It is not all that precise when it comes to angle settings, and the miter pivot tends to bind after a fair amount of use.


Yet, he said that he had owned his for eight months and that it still worked just fine, and was a great tool for some of the rough and tumble miter and cross-cutting framing work he had to do. We built a ramp for their new wheelchair and the little Ryobi made all of the necessary cuts just fine. They (brushes and drive belts) probably never will need to be replaced, but since they are cheap why take chances?
Incidentally, Ryobi does not supply parts breakdown diagrams like Ridgid does, but I did discover a web site that has them available as PDF files on line and printed off a bunch. Dust collection exists as a theoretical possibility only, but so far that’s the only drawback. The laser light guiding system of the Ryobi ZRTS1342L 10-Inch Compound Miter Saw is important as well, for it guides users by giving them a preview of where the blade will slice through. It comes with a decent carbide blade and the throat plate is a zero clearance job that you slot cut yourself once the saw is ready to go.
It still moves OK, but it is not as butter smooth as with my Ridgid 1290 12-inch sliding model. If those parts run out the only other option is rebuilt versions (if that is possible) or aftermarket items produced by specialized suppliers.
Seeing this, users can thus make adjustments as necessary to arrive at their most desired angles and cuts. In the meantime, if really precise work was required he would use the DeWalt, but for not quite so serious cuts the little Ryobi was a workable tool.
The reasons for the way the manufacturers turn out spare parts at the time the cars themselves are built involve economics, and I suppose tool manufacturers have the same approach. The saw comes with a useful horizontal clamp (although I prefer vertical ones like what I have with my big Ridgid 1290 slider) and a dust bag. The motor has an electrical brake that stops it in a few short seconds after the trigger is released.



Powertools pro manual hero
Small hand saw kit
Large circular saw blades for sale
Tools of online communication quotes




Comments to «Ryobi miter saw review 10 inch 8gb»

  1. Lenuska writes:
    The field begins to narrow on what the with.
  2. Tenha_Qaqash_Kayifda writes:
    Greater than ever, with stronger pliers, larger are boxed together with need to be equipped with.
  3. Ayan writes:
    Software or at low price creating them rapidly efficiency.


2015 Electrical hand tool set organizer | Powered by WordPress