23.07.2013

Wiring a light switch for ceiling fan noise,buy cheap hand fans,discount minka fans review,home depot lighting kitchen fixtures - Step 1

Author: admin  //  Category: Quiet Ceiling Fan


I will be running new wires to a master bedroom renovation and would like to wire the ceiling fan (a Hunter) so I can control the light and fan independently from two locations. I'll check to see if a remote module can be added to the fan, but I'm also trying to cut down on the remotes on the nightstand! For speed control, you can just substitute a 3-way speed control for one of the fan switches shown in Hammerlane's drawing. Go to my Switch Terminology Page where I discuss the terms used for the different types of home electrical switches. When wiring a 2-way switch circuit, all we want to do is to control the black wire (hot wire) to turn on and off the load. All ground wires (bare copper) are all now connected (incoming ground, load ground and switch ground). Now by understanding the diagram above, go up to the top diagram and by using the concept shown here, just use your mouse pointer on that diagram and follow the flow from black wire (hot wire) to the load and return through the white wire (neutral). So now that you have a basic concept of wiring a 2-way switch, let's look at the following 2-way switch diagrams to see which type of circuit scenario you have. Cable A and Cable B are the live, neutral and earth loop to each of the lights in the circuit, (Cable A feeds in the live supply from the previous light in the circuit and cable B loops out to supply the next light in the circuit) these cables remain ‘live’ even if the light switch is off, this is why you should ALWAYS make sure the circuit is isolated before you start work. If the number of red & Black wires doesn’t quite tally-up with that shown above, one of the following will be the case. Fig 3 – shows the last ceiling rose on a circuit and therefore there is only two cables present, cable A is the live, neutral and earth supply, cable C is the twin Red and Earth to the switch.


If the cables in your ceiling rose are Brown and Blue and not Red and Black as shown above then see the alternative wiring diagrams. Home Improvement Stack Exchange is a question and answer site for contractors and serious DIYers.
When I wire up this one up according to the diagrams available online I find I can't switch the lights off.
I guess this question looks much like this one, but the best answer has the same diagram I feel I have worked from (except different colour scheme). One of the brown wires will bring power to this point, another will go to the switch, and the final brown wire continues on to the next light.
You need to connect the brown that has constant power, to the brown that goes to the switch.
As you currently have it wired, you have the wire that feeds the other lights connected to constant power. Disconnect all brown wires, and position them so that they are not, and will not come into contact with any other wire or metal object. If you got a voltage reading on more than one wire, STOP, do not follow the rest of these instructions.
Not the answer you're looking for?Browse other questions tagged electrical light-fixture or ask your own question. If you want it on a wall control, there are only a limited number of fans with that feature.


This simple diagram below will give you a better understanding of what this circuit is accomplishing.
By wiring a 2-way switch, The circuit below shows the basic concept of electricity flow to the load. This should give you a good basic understanding how the 2-way switch circuit works and will help you in adding or changing a 2-way switch.
After you have pulled your switch out from the wall, the wires in the box and connecting to the switch should look like one of the following.
1 here the electrician has used twin and earth for cable C (Red and Black) instead of twin Red and Earth as the switch wire, the Black conductor should really be sheathed with Red sleeving to show it is a live conductor, if it is not, before attempting to replace the ceiling rose you should mark this conductor with either Red sleeving or insulating tape to avoid problems when reconnecting the ceiling rose. Next connect the markered blue to the light, and to the brown wire that leads to the other lights on the circuit.
First of all we need to go over a little terminology so you know exactly what is being discussed.
The Green screw on the 2-way switch is for the ground so all ground wires should be connected as seen below. The electricity flows from the hot wire (black) through the 2-way switch (shown in off position) and then to the light and returns through the neutral wire (white).



Hunter ceiling fan type 3 troubleshooting
Best room to room fan muffler
Watch funny games 1997 online free
Ceiling fans naples fl jobs


Comments to «Wiring a light switch for ceiling fan noise»

  1. orxan_yek writes:
    Fans have four lights and certainly never want a fan that is as well.
  2. Azeri writes:
    Back into the housing (Photo that let for independent fan and light control complication, fans.
  3. joni writes:
    Because of its superb function must also be able to see the.