Replace battery braun professional care toothbrush amazon,backup battery for cpap machine,truck battery not charging quickly,samsung galaxy s3 32gb battery life - You Shoud Know

02.09.2014
This amount includes seller specified US shipping charges as well as applicable international shipping, handling, and other fees. Estimated delivery dates - opens in a new window or tab include seller's handling time, origin ZIP Code, destination ZIP Code and time of acceptance and will depend on shipping service selected and receipt of cleared payment - opens in a new window or tab. This item will be shipped through the Global Shipping Program and includes international tracking. Will usually ship within 1 business day of receiving cleared payment - opens in a new window or tab.
Due to the nature of battery installation, NO return is accepted after installation as it will no longer be in its original new condition for resale.
By submitting your bid, you are committing to buy this item from the seller if you are the winning bidder. Some type 4729 brushes are fitted with slightly larger batteries so do double-check before ordering!We now have a repair guide available for replacing the battery in the Braun Oral-B Type 4729 toothbrush so take a look! Contact the seller- opens in a new window or tab and request a shipping method to your location. If you reside in an EU member state besides UK, import VAT on this purchase is not recoverable.
Uninstalled product is returnable, within 30 days of delivery, with a restocking fee of either $3.99 or 20% of total payment, whichever is greater, to cover the original shipping and handling fees and various fees charged. Item returned without our authorization will be refused on delivery and sent back at the sender's expense. Video Published for Repair of Braun Oral-B Triumph v2 Toothbrushes FDK Batteries now in stock – Just what Braun ordered! The tutorial is based on the Type 3728 model but may be applicable to similar models such as the Type 4736.


Put the brush on its charger and gently twist it anti-clockwise to release the catches holding the base of the toothbrush into the handle.
Carefully extract the inner workings of the toothbrush without pulling on the thin copper wires. Put the brush on to charge for a full 24 hours and check that the charging light starts to flash. Please recycle your old battery either at a local civic amenity or a supermarket collection point.Please leave any questions or comments about this guide on our dedicated blog post here.
The tutorial is based on the Type 3756 Professional Care 1000 model but applies to other 3754, 3756 and 3757 types including the Professional Care, PRO and TriZone 600, 1000, 2000 and 3000 models and others.
Standing the toothbrush tip-first in hot water (60 degrees C) for 5 minutes will help to soften the plastic and make the ring easier to remove. Note that the ring is stepped so you might need to press down into the soft coloured surrounding material to lever the ring from underneath. Then it’s on to the copper wire solder points for the charging coil (arrowed below, right) and the pressure warning light (arrowed below, left). Carefully desolder these and lift the wires away from the circuit board trying not to melt the plastic around them. Because it is physically larger, a longer battery will have a higher electrical capacity (mAh) and will run for longer between recharges.
Do you notice how the metal tag on the positive terminal extends horizontally away from the battery? The original-sized 42mm x 14mm batteries available in our shop are 1400mAh capacity and the longer 49mm x 14mm batteries are 2200mAh, over 50% higher capacity! The base of the handle will not rotate, move or open but this will help to loosen the seal.


Now, holding the charger and the toothbrush gently bend the handle backwards so that the base starts to lever open. Standing this end of the brush in hot water for 5 minutes before bending it back will help to soften the plastic and will make the clip release more easily and be less likely to break. If you previously didn’t remove the retaining ring you will need to push hard from the top by holding the brush upside down and pressing the shaft on a hard surface.
If you didn’t manage to remove the retaining ring at the start you should be able to unclip it now.
Carefully unclip it from one side, then the other: Time to get your soldering iron warmed up now! Using the soldering iron and desolder pump carefully desolder the two battery terminals on the circuit board (arrowed below) and bend the metal tabs vertical and away from the board with a knife so there is no solder left joining the solder tag to the board.
If fitted, locate the solder point for the pressure warning switch (arrowed below) and desolder it. Very carefully start to narrow down the width of the negative terminal solder tag by first snipping into the tag from the side. Don’t try to cut into it half way in one go, just try to cut a quarter of the way in from the side and it will tear to half way. This is from the factory that makes the Sanyo batteries and also the Varta batteries in our shop. Once you’re happy with the aligment click below to move on to:Reassembly Recent Posts European Union Customers can still buy from our Shop!




How to change an audi a4 car battery
Old iphone 5 battery life


Comments Replace battery braun professional care toothbrush amazon

  1. Diabolus666
    Monitor charging mode, connection status chart about.
  2. mambo
    The speed and power of an impact driver (Starting.