Change car battery step by step 0-2,reconditioned smartphone battery 4000mah,lead batteries work worksheet,honda hybrid battery rebuild guide - Easy Way

20.12.2014
You’ll first want to ensure the vehicle is off, in park, and remove the keys from the ignition.
Car batteries are typically very heavy, between 40-60 pounds, so keep this in mind when lifting the battery out.
At this point you’ll want to clean off any residue or corrosion in the battery trap, from the hold-down strap, and the terminals of the cables.
Once everything is clean and completely dry, place the new battery in the vehicle’s battery tray. Optionally (but recommended) you may spray each of the new terminals with a small amount of anti corrosion solution in order to get the most out of your new battery and to prevent having to clean off corrosion early on. Carefully re-attach the cables to the terminals, taking care to place the red cable on the red terminal and the black cable on the black terminal. Once you’re confident everything is done, secured, and in place snugly, do a quick once-over.
We hope this guide properly explained how to change a car battery so you can save some money by doing it yourself instead of paying for someone at a garage to change your car battery.
About Latest Posts Lee Porter Latest posts by Lee Porter (see all)Car Polish and T-Cut, What’s the differences?
One of the most common things to go wrong when you’re least expecting it is the car battery. However, it doesn’t have to be like this and it’s actually quite easy to change your own car battery before it comes close to the end. The first thing to do is to turn off your engine and ensure the car is parked with the handbrake on. Next, open up the bonnet and place a blanket over the bumper and front of the car to prevent issues with battery acid burning through paint. Often the battery tray will be rusty and in this case it’s best to clean it with a little baking soda diluted in water. Next, lift the new battery up and place it on the tray making sure that you get help if it’s too heavy. Your car’s battery should now be fine and there should be no real worries about coming out one morning and it being dead.
Finally, bring the old battery to the recycling centre to ensure that it is disposed of properly.
These tips will ensure you can remove, fit and also go the right way around recycling your old battery and prevent any issues.
The process is virtually identical for all makes and models of vehicles unless you have a specialty hybrid or electric vehicle, at which point you would need to refer to your dealership. Place the strap you previously removed back over the new battery as it was before and secure the clamp via the method you previously used to remove it, making sure it’s securely in position and doesn’t move around at all.


You may need a wrench in order to loosen the bolt enough to wiggle the cable free from the terminal.
Secure your new battery in place with the hold-down strap you previous removed and ensure it’s tight and snug as you don’t want the battery moving around or shifting while you drive.
Try and move the battery back and forth in place to ensure the hold-down strap is on and secure.
Visit Car Cosmetic’s blog to find more helpful tips and guides to keeping your vehicle in tip-top shape! We all know the feeling; we go out one cold morning only to hear the sound of the battery dying and the car failing to start. It will save you on the price of garage fees and ensures your car doesn’t have a malfunction of any sort. This is because they often can fall off the battery and disappear into the engine never to be seen again – an issue we often hear about at Alpha Batteries.
Batteries can cause all sorts of environmental issues, so ensuring it’s recycled in the right manner will prevent problems.
In order to change your car battery, you’ll want to first make sure the vehicle is off with the keys removed from the ignition. Once that’s loose, you should be able to lift the battery out of the tray it sits in by lifting it up and out. Most new batteries come with plastic caps over the terminals; one on the red and one on the black. Once tightened, wiggle it back and forth to check that it’s tight enough and won’t come loose during road vibrations. Prop the bonnet up using the rod in order to lock it in place while you work under the hood. Otherwise, lift from the bottom and place the battery safely outside of your engine compartment. You may use battery cleaning solution (also found at your local garage) or a simple mixture of water and baking soda. Do each cable in one-step; only moving on to the black cable after the red cable is completely on and tightened down properly.
If you have any issues starting your car, go back and double check the terminals and cables are connected and tight. If the vehicle has a negative grounding, add the positive first and if it’s a positive grounding place the negative firstly. It might cost a few dollars or pounds to do, but you know you’re not seriously damaging the environment. Open the bonnet and prop it up as we’ve covered in a previous guide on how to open your car bonnet.


You don’t want to remove the nut entirely, instead, loosen it enough to where you can wiggle the wire off the terminal. Locate your battery; in most cases it will be on the right-hand side of your engine compartment.
A few gentle taps to the side of the cable after loosening the bolt should be enough to remove the cable. If there is heavy corrosion crusted on the cable connectors, you may need to use a wire brush or look into a battery cleaner at the shop.
Do the negative one first and then the positive.Removing each cable one at a time and placing it out of your way. Locate your battery; it’s a large rectangular object with a red and black terminal with some heavy duty cables clamped to either side. If there is significant resistance and the bolt is sufficiently loose, wiggle the wire up and down to free it up. Next, you’ll ideally want to lightly spray each individual terminal with a coat of anti-corrosion solution. While you’re done at this point, it’s a good idea to go back over each step to make sure everything is snug and secure while maintaining a good connection to the terminals. It will be large and rectangular with two thick cables coming from the battery terminals which are colour coded Red and Black.
In some cases, major corrosion can make it very difficult to remove the cable in which case a Battery Terminal Puller is recommended and is sold at most garages. Using either battery cleaner or a mixture of baking soda and water, clean off any corrosion residue left over in the tray where the old battery was. While this is an optional step, it helps your battery to last longer by avoiding corrosion buildup you’ll find on most old batteries and prolong the best connection. If the battery cables move around, you may not have a good connection and it may not start due to a weak connection. If you can’t find it there try looking in the boot, on some models the manufacture decided to placed it there to safe space in the front. The cable should come off easily unless you have corrosion damage, at which point you’ll want to look into a battery terminal puller; however in most cases that’s unnecessary.
Using a wire brush, clean off the battery connectors to free up any rust or corrosion to ensure a good connection to the new replacement.
Repeat this process for the red terminal and set each cable to their respective sides of the battery allowing room to perform the next step.



Car battery life playing music youtube
Everstart marine maxx 125ah deep cycle battery
Ups battery 12v 26ah price
Car battery discharged how to start


Comments Change car battery step by step 0-2

  1. LaDy_CooL_BoY
    Battery cells which is what enables the higher.
  2. LUKAS
    So I contacted customer service and was told the then the battery.
  3. HAPPY_NEW_YEAR
    Replacement battery needs to match the see that.