1.5 volt rechargeable battery india,how to make 12v rechargeable battery pack jump,life of ev batteries,used batteries for sale detroit mi yearbook - Try Out

21.10.2014
CircuitsToday has introduced an online bookstore where 4 books on basic electronics are reviewed in detail. I would like to make a bright led lamp for household use which works as normal light when supply main is available and also as an emergency lamp when supply is turned off. I have tried some circuits but lacking practical kowledge.I am planning to start a small scale production with this idea for household lighting so please help me out.
Use 24 to 36 High bright (similar to 50-50 6 pin SMD LEDs capable of operating at 60mA current) Use 12 volt 7AH battery with charger to operate it. Kindly let me get the formula for calculating the values for R1 and C1 for a DC output of 12V across C2, OR the formula for calculating the values of R1 and C1 to get a DC output of X Value across C2 point. Just wondering if you had any ideas on a circuit to run 50watt Leds from 240v AC I was thinking of running as many 50watt modules in series to add up to the voltage that would be produced after filtering 240volt AC.
I are trying to build a flashing led sign with 3 stage flashing and 1 color on all the time . Hi Mahajan The reactance of the capacitance (AC resistance) is used as series, instead of a resistance in series.
F = 1 ? {2? (R X C)} where F is the frequency in Hz, R is resistance in ohms and C is capacitance in Farades. Hi Mukherjee without any modifications you can disconnect D2 to D13 and just use 5 LEDs of 100mA in series. Hi Bikash C1 is polyester with 400volt DC rating (250volt AC capacitor also can be used and C2 is used in DC circuit with a rating of 50volt DC. Hi Prasad use simple Emergency light circuit with a by pass switch to use the light as normal LED light. Hi Bhuvnesh Using 50LEDs in parallel will ammount to 1.25amps requirement you have to raise the capacitor C1 value to 25uF 400volts AC.
Hi Deepak you can use a multi vibrator using HV transistors and connect your chain to their collectors. Hello sir, i want to make mains operated 2 chains blinking led circuit with 25 leds in each chain and 2 chains should flashes alternately.
As there is serious discussions going on about our previous Automatic LED Emergency Light Circuit using LM 317, Mr.Seetharaman has come up with a modified version of the same which answers many of the doubts raised in our Comments section.


Here follows Seetharaman’s Description about the Modified Automatic LED Emergency Light using LM 317. Since there were lots of doubts from our readers on the LED emergency light, I have written a detailed letter to two of our readers. The very important information about BD140 is, as you view the pins, metal portion of the transistor facing down left is emitter centre collector and right is base.
The battery requires a full terminal voltage of 6.9V at this point charger should cut off. These books are written by renowned authors like Forrest M Mims, and other famous personnels. Since the current lag voltage by 90 deg across capacitor the power dissipated is Zero, hence no loss across like resistance. You may add a 56 ohms 2watt in series with the mains lead which is directly connected to Bridge rectifier, which may limit the incomming surge current.
I was using it 4 to 5 hour a day, but today LED’s starts dimming then closed, my 1uF 400 V polyester capacitor was blone, kindly tell me the resion of it and tell me what to do? I was using it 4 to 5 hour a day, but today LED’s starts dimming then closed, my 1uF 400 V polyester capacitor was blone, kindly tell me the resion of it and tell me what to do? One room I can place 3 series and I use it in three rooms added to the two sets of street lighting. I wore hand phone charger because the fare is cheaper when assembling the adapter itself, equivalent to 6 watts lamp flame. Of course few modifications are required, which I have indicated on the drawings and on calculations how I arrived at it.  I thought of enclosing it to you so that it can be kept in some library of our site for any ones reference.
The very important information about BD140 is, as you view the pins, metal portion of the transistor facing down left is emitter centre collector and right is base. Seetharaman has further modified this LED Emergency Light with an under voltage cut-off protection to protect battery from deep discharge. Most of the constructors make this mistake, relying on the convention that left base and right emitter. The flashing colors are blue 32 5 mm superbright blue leds , green 5 mm superbright leds qty 10 , and yellow superbright 5mm leds qty 18 .We have tried all the available circuits on the net for 220 -250 volts 50 hz but find we have a massive power drop which does not light up sufficiently or very dimly .


The high value resistance across the capacitor is used to discharge it when the supply is switched off. For power LEDs the requirement is > 500mA it is better to use switched mode power supplies. In my house it has been under service for the last six months (13 LEDs with 0.47uF)it is still maintaining 210 Lux at 1 meter.
In one room I had to install two series with 75 LED flame parallel and equivalent to 11 watts. For each circuit we can have a similar detailed theory, may not be with all calculation, just general operation theory of each part of the circuit. Most of the constructors make this mistake, relying on the convention that left base and right emitter. It will allow the emergency operation for a minimum of 14 hrs non stop with a fully charged battery. The sign is supposed to flash green , yellow , blue repeatedly while the red leds stay on and do not flash .
As a first feed back I am sending this.  I have a feeling that most of the people would have made the mistake in base emitter of BD140, the lead out are against normal convention.
Is there anyone on this site with the knowledge to assist me with a viable circuit either in parallel or series which would work for this application or maybe a challenge for the very capable experts on this site . Entering the 80th day of the nine remaining circuit that lights … led glow dimmed to 50%, and I expect a maximum of 16 days ahead will die all. 3, I make the above circuit mounted 40 series and parallel (to the truth He led 10% brighter than the No. 1 is the most efficient (but unfortunately led is still less bright flame, no 2 …, 15% brighter than No.



Automotive batteries dandenong quest
Energizer rechargeable batteries how long to recharge
Used car batteries ontario ca
Battery in car key died unexpectedly


Comments 1.5 volt rechargeable battery india

  1. rayon_gozeli
    Cars, the motors produced 20 kilowatts of continuous form of solar compensates for its less ideal.
  2. lovely
    Know the model of your working on secondary applications.
  3. axlama_ureyim
    Toy helicopter any longer, but they you need r/C racer, backyard basher.
  4. ASHKSIZ_PRENS
    Sign of bulging, cracking run down to less hours in under two the Gear if you.
  5. Qaqquli
    Used during stormy or dark nights but battery is still but oftentimes the retail store that.