If your iPhone 4S headphone jack or mute switch is giving you issues, a DIY repair on the cable that handles those functions can remedy the problem.
Regardless whether you're having headphone jack or mute switch issues on your iPhone 4S, this guide can walk you through how to get both functions back in working order again. Disclaimer: As with any repair, iMore can not be held responsible for any damage you may do to your device. If you are comfortable with repairing your own device, put your ninja pants on and keep reading! We recommend using only quality and genuine parts from a reputable supplier like eTech Parts.
While the video walkthrough adds even more detail, it is meant to be used in correlation with the written steps below. Using your security screwdriver, remove the 2 screws on either side of the dock connector port.Set them aside.
Using your #00 Phillips screwdriver, remove the two screws holding the battery in place.These screws are different lengths so make sure you remember which one goes where. There is a tiny grounding clip underneath the battery clip where the first screw is located. Using your spudger or pry tool carefully disconnect all the cables at the top of the logic board. Once you unclip the seven cables, you can lift the rear-facing camera directly out of the iPhone. Using your #00 Phillips screwdriver remove the shield that is covering the dock connector cable towards the middle left of the iPhone. Using a SIM removal tool or a bent paper clip, eject the SIM tray and set it, and the SIM card aside.
Remove the three #00 Phillips screws at the top, middle, and bottom left of the logic board with your #00 Phillips screwdriver.
Start by removing the screw holding on the upper antenna with your #00 Phillips screwdriver.Using a metal spatula or pair of tweezers, peel the upper antenna away from the headphone jack.
To replace the headphone jack and mute switch cable, follow the removal instructions exactly in reverse. To reassemble your iPhone 4S, you can either follow all these directions in exact reverse order or view our reassembly video guide above which will walk you through how to reassemble it from screen to turning it back on and testing it. Once you've gotten your iPhone 4S completely reassembled and you're positive you don't have any leftover screws, you can go ahead and turn the device back on. If you've run into issues or things aren't going the way you thought, our DIY and mod forums are a great place to start.


An apparent security vulnerability has left iPhone users susceptible to having their phones shut off with a simple text message. The security loophole gained widespread attention on social media Tuesday night, with individuals sending the string of code to friends as part of pranks or to simply see if it worked.
Next time someone with an iPhone pisses me off, I'm going to send them that effective power text.
From the breaking news you need to know to the hottest trends circling the Web, TheBlaze has it all. The other day I was jailbreaking my iPhone, but before doing so I had to put my iPhone into recovery mode.
Now there is a handy free tool, RecBoot, for Windows, Mac, and Linux users that can take an iPhone out of recovery mode. If your iPhone is stuck in recovery mode you’ll likely find RecBoot to be an invaluable tool.
How remove sim card iphone ipad imore, My wife wouldn't know how to remove the sim on her iphone.
All iphone sim card, All about the iphone sim card, including where it's located, how to remove it, and whether it carries a sim lock.. Moving iphone 5s sim card samsung galaxy s5 - visihow, The sim card adapter purchased put apple iphone 5s' sim card samsung galaxy s5 put sim card correct place galaxy s5. Symptoms typically include audio cutting in and out when headphones are plugged in or no sound at all.
It's also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty.
It will show a complete breakdown of the device but smaller steps for each individual repair will be listed with high quality images in the actual guide below. It should come up easily so pry up gently.You'll notice that it is wrapped around a metal clip. Use the area that the rear-facing camera was located and the bottom of the logic board to lift it straight out. Please note that you may have to transfer the metal brackets to the new cable if the replacement cable you purchased did not come with the brackets pre-installed. Once it is securely in place you can replace the metal retainer by snapping it back in place. For a headphone jack and sensor cable replacement, you'll need to watch from around 5 minutes and 3 seconds to the end of the video.
In this case you’ll want to use RecBoot Exit Only which will take your device out of recovery mode.


The mute switch can also face issues where turning vibrate on or off results in no response or the switch itself being loose.
One of the cables lies underneath the bottom most cable so you'll need to disconnect the cable over it before folding it back and revealing the shorter cable underneath. Gently lift the shield out of the iPhone and set it aside.Take your spudger tool and gently pry up the dock connector cable and peel it back as shown below.
Take care to pay attention as to how it was laid so you know how to put it back during reassembly.Use your tweezers or a pry tool to carefully loosen the noise canceling mic from the upper frame.
Since we've replaced a cable that controls both the headphone jack and the silent switch, make sure you test both thoroughly to make sure that they're working correctly. After doing that you’ll be prompted saying that you must restore the device back to the factory defaults.
Once you’ve done that you can fire up the RecBoot app and choose whether you want to Enter Recovery Mode or Exit Recovery Mode. The good news is that on a Mac you don’t have to worry about copying the DLL over, and it should just work out-of-the-box. These problems don't typically involve the actual mute switch, but the cable that lies underneath it. It is stuck down with a good amount of adhesive so be careful when prying upwards that you don't bend the battery.
Make sure you don't lose it as you'll need it for reassembly.There are two more screws holding the logic board in place and you'll need to remove them with your flat head screwdriver.
Now that the metal retainer has been removed you can gently lift the front facing camera out of the iPhone 4S. For awhile getting yourself into this mode meant that you must restore, and there was no turning back. If you’re reading this post you probably want to exit recovery mode, which will get your iPhone back into the state it was prior to entering recovery mode.
Take care not to rip the cable by pulling up to quickly.Leave the cable in this position and move on to the next section.
You'll only want to loosen it enough so the adhesive completely breaks.Again, using tweezers or a pry tool carefully pull the headphone jack assembly out of your iPhone 4S. If one part is resistant move your pry tool a little further down and gently start prying it up in different places taking care not to come too close to the volume button cables towards the top.Once you've gotten the battery pulled out of the iPhone 4S we can move on.



Great photography spots in san diego 2014
What is the best lens for landscape photography canon


Comments to «How to get pictures off iphone for mac»

  1. AYAN on 10.05.2016 at 19:38:25
    Laski, picture and video director of The Hollywood.
  2. 1989 on 10.05.2016 at 21:33:34
    Many of the methods which can be at the moment used in creating.
  3. BAKULOVE on 10.05.2016 at 17:54:10
    Middle, and that the main pSD (which stands for.
  4. zZz on 10.05.2016 at 13:12:49
    Technique to give usually by way of Facebook / periscope from right.
  5. EFIR_QAQASH on 10.05.2016 at 15:34:47
    Simply select an image you they're extremely useful modes to shoot.