Remember that you have to use a good wooden board, otherwise your bird house might not be as durable as you plan.
Don’t forget that these dimensions are a starting point and you can adjust these dimensions according to your needs and tastes. Smart tip: We recommend you to pre-drill holes along the edges of the wood pieces, before driving in the nails, otherwise the wood might split. Step 3: Mark the components on the wooden boards, using an L-square and a carpentry pencil. Smart tip: Check attentively the wooden board before drawing the pieces and try to avoid the damaged areas.
Step 4: Use a jigsaw or a circular saw to cut the sides and the front and back ends of the birdhouse.
Step 5: Mark the sides of the birdhouse on the wooden board and cut them in the same manner described above. Work with great care and wear eye protection while cutting the board with a circular saw or a jigsaw. The main components of the bird house have been cut: the front and rear gable ends and the sides. Smart tip: Use medium-grit sandpaper, if you want to get the job done quickly and in a professional manner. Step 8: Join the front and side of the bird house together, as you can see in the image, making sure the components are align properly. Step 9:  We recommend you to use several C-clamps to lock the components  tightly and leave the glue to dry out for about 5 minutes. You should notice that the both components of the bird house are aligned properly and the corner is right angled. Two nails for each side of the front gable end are enough to secure the birdhouse  properly.
Work with patience and make sure you align the components properly before drilling the holes.
Drill the pilot holes along the side edges of the rear gable end and insert the finishing nails, by using a hammer. Usually the location of the birdhouses should be towards the top of the front end, but you should set it according to your needs and testes.
After you have cut the round entrance, you should clean the birdhouse thoroughly with a vacuum cleaner. After you set it into position, making sure it is aligned perfectly with the other components, you should predrill two holes on each side, by using a drill machinery with torque control and a small drill bit. In most of the cases, we lock the floor of the bird house by driving in several nails, as the birds will clean it by themselves. First, use a drill machinery and a small drill bit to make on pilot hole on each side of the birdhouse. Smart tip: In order to hang it to trees, you should use a proper hardware and a piece of wire or a small chain. Thank you for reading our article on how to build a bird house and we recommend you to check out the rest of our projects.
In order to obtain a neat look, we recommend you to use quality wooden boards with a nice finish.
In order to fasten the wooden pieces together, you have two main alternatives: on one hand you could use screws, while on the other hand you could try to drive in nails. First of all, you have to choose the design and dimensions of the birdhouse from the very beginning.
Building this birdhouse doesn’t require expertise in the field, but just a few basic woodworking techniques, like drilling pilot holes, inserting nails and cutting wooden boards with a circular saw. The wooden birdhouse shouldn’t be too large nor too small, otherwise the birds might not move in it. In order to reduce the cutting waste, you should use a 1×6 wooden board and draw the guidance lines with an L-square.
After you have cut all the needed pieces for the final assembly, you should smooth their edges with a sanding block. As you can see in the image, putting together the simple birdhouse is really easy, if you follow our step by step plans.
Building a simple birdhouse is a straight forward process, if you use the right plans, materials, tools and techniques. Use the L-square to draw straight lines on the wooden board and the jigsaw to cut the pieces accurately.
After you have cut the wooden pieces, you have to smooth their edges with a sanding block and to apply wood glue on their edges before locking them together.
Smart Tip: Fasten the floor of the wooden birdhouse with screws (if you want to clean the birdhouse, just unscrew them and remove the floor).


Thank you for reading our article about simple birdhouse plans and we recommend you to check out the rest of our projects.
It came as suddenly as daylight savings: an early morning birdsong riot that actually startled me from sleep.
Just wanted to add that your fun and interesting directions for multiple bird house designs make creating with your hands more enjoyable. In anycase cut out all the parts last night and me and my daughter are putting it together tonite with the air nailer. Spy watch are usually turning out to be more and more favorite to get business security, nonetheless additional importantly intended for house security. Download Free Woodworking Plans and build this Wren and Blue Jay House compliments of your woodworking friends at Shopsmith . Free birdhouse plan shows how to make a simple wooden bird house suitable for small nesting birds. Best Answer: The size of bird house you build depends on what type of birds you are trying to attract.
Cardinals are not cavity-dwelling birds, so a cardinal birdhouse is actually more like a cardinal bird platform. Free Birdhouse Plans – This page provides birdhouse build plans for a cedar board birdhouse. Build a better birdhouse Start with our directions for a basic wood shell, then embellish as you like. Building bird houses is a fun project, especially if you show your kids how to work with several tools and how to use a regular wooden board to create something unique. In addition, make sure the wood is not treated with toxic substances, if you plan to install it in your backyard. First of all, you need a jigsaw or a circular saw to cut the main components of the bird house, but a handsaw would work as well, though it would take longer. If you haven’t built a birdhouse before or if you like our project, you should use the bird house plans you can see in the image. Therefore, we recommend you to use an L-square to draw the components on the board, a jigsaw or a circular saw to cut the wooden pieces and a hole saw to cut the round entrance of the bird house. Work with great care and make sure you use the right dimensions, otherwise the pieces won’t align properly.
We recommend you to lock the wooden board into place before cutting it, otherwise it might move and damage the components. If you have followed our tips, they should be equal (the front with the back, the sides) and align properly.
Work with great care and move the sand block several times over the edges until they are smooth enough for your tastes. As you can see the difference is noticeable, but we still have to sand it several times, to get the desired result. Even though it is not compulsory to use wood glue, we recommend you to use it, as it will increase the bond between the wood pieces. Even if these aspects might seem minor details, we recommend you to pay attention, if you want to build a durable bird house. From our experience, we don’t recommend you to use too much force when hitting the nails, as you might easily damage the wood.
Building birdhouses is easy if you have cut the wooden pieces at the right dimensions and use the right plans and techniques. In order to do it in a professional manner, you have to mark it on the center of the from end. Before inserting the nails, make sure the narrow side of the roof is perfectly align in every direction.
Nevertheless, you should know that you might secure the floor to the birdhouse by using hinges, if you want to have access to it anytime you want.
Irrespective of your choice, we hope that you new bird house will bright up the look of your backyard and offer a cozy home for your favorite birds.
Don’t forget to SHARE our articles with your friends, by using the social media widgets.
Building a simple birdhouse for your kids is a fun and quick project, which should freshen up the look of your garden and be a great opportunities to pass them down several basic woodworking skills. However, before building the wooden birdhouse, you have to make sure the wooden boards are not treated with toxic substances, otherwise the birds might be affected on the long run. In most of the cases, we recommend you to insert finishing nails, as they lock the pieces together properly and their heads are almost unnoticeable. If you want to build a simple birdhouse for the kids, without spending too much money or time, we recommend you to use our free plans. As you can see in the image, you just need to buy a regular wooden board, which shouldn’t cost more than 5 dollars.


If you want to obtain accurate cuts, we recommend you to clamp a guidance fence with several C-clamps. If you haven’t worked with a jigsaw before, we recommend you to clamp a guidance fence on the wooden board.
Don’t forget to share our articles with your friends, by using the social media widgets. Connected with all the merchandise of which cope with home safety, surveillance dvr tend to be generally forgotten.
Check out more great simple recycled craft projects, you can also subscribe to my RSS feed or get regular updates from Silly Simple Living via email. There are plenty of birdhouses that you can buy, but nothing beats the feeling of building your own beautiful wood birdhouse. Cardinals are one of the most common birds that could be found in the backyard of most homes in eastern America. Plans and instructions for building bird houses, books about birdhouses, and links to other information about birds and nesting boxes. On the other hand, you can build a simple and cheap bird house (around 2-5$, according to its complexity) and give it as a gift to someone special.
On the other hand, if you want to obtain an unique design, you could reuse several old wooden boards, after you make sure they aren’t rotten.
Next, if you want to obtain a neat result, we recommend you to cut the round entrance using a hole saw drill bit and a drill machinery. Building birdhouses is a lot easier if you know its dimensions and design from the beginning of your project. Use an L-square to measure the center of the dird house and mark it with a carpentry pencil.
From our experience, we consider that a hole saw drill bit will make the quickest and most accurate cuts. In this manner, you will be able to install the perch without being noticeable from the inside of the bird house.
Even if you are not accustomed to these kind of diy projects, you should get the job done in a professional manner, especially if you use our easy to build plans and follow the step by step tutorial. When buying the wooden boards, you have to choose the best of them, without any visible flaws (the boards must be straight, without twists, splits, wanes, or decays). Nevertheless, don’t forget to make pilot holes along the edges, before inserting the nails, to prevent wood cracking. Alternatively, you can build the back of the birdhouse longer, to attach it to a tree with several screws, as you should notice in the image. I eased into it slowly at first, dreamy-eyed on a pillow; then barefoot outside with coffee.
Many hidden cameras and Audio Bug excellent for dwelling security cost significantly less as compared to $300.Double zero. All you need to get the job done in less than an hour is to use a 6” wide wooden board and several basic tools (a jigsaw and a drill machinery with a hole saw drill bit).
Last but not least, the boards should have the same thicknesses over the whole surface and be as straight as possible. Last but not least, you need a hammer to drive in the finishing nails, when locking the bird house together.
After you have built the birdhouse with your kids, you should apply several coats of paint to give it a beautiful design.
It fiddled throughout the afternoon, as chirping goes in the first weeks of spring, while the boys dug in the fresh earth. Nevertheless, before buying the materials or using waste pieces, you need to draw a plan, starting with the dimensions of the wooden bird house up to its final design. Work with great care, pay attention to details and you will build a beautiful home for the birds in your backyard.
From our experience, we recommend you to decide from the very beginning the design of your decorative bird house, otherwise you might not like its final shape. Actually that owl house was built from those pickets – only I glued a half ripped picket to glue to a full picket to make the size I wanted. So it seems we have to hustle this week to complete what we had earmarked as a winter project: building bird houses. Quite possibly, they are already using what we’ve left out to build their own nests in the trees, but the wood is ready in the garage and our hands are empty and poised for work.




Pent shed with log store
Shed plans 8x8