How to run low voltage landscape lights,free landscape photos mountains \u002b lakes,rendered retaining wall ideas,green key landscape services - Plans On 2016

13.08.2014
Directional lights are used when a concentrated beam of light is needed on statuaries, columns, signage, and water features. Once the lighting system is installed, there are three checks you will want to make to ensure everything is functioning properly. A successful outdoor lighting plan requires selecting the right fixtures, then placing and wiring them correctly. When lighting a path, decide whether you want to light only the path or both the path and the features around it. Install the path light by digging a hole deep enough so the top of the PVC footing is level with the ground surface. Test each light fixture for its voltage level with a digital voltage meter (about $25 at Radio Shack). The farther a light is from the transformer (and the more lights installed between it and the transformer), the less light it will put out. In order to figure out what size transformer you need, you should add up all the wattage on the bulbs your lights use. For good measure once all the lights are working, wrap the connectors in Scotch Heavy Duty All-Weather duct tape to keep them sealed and connected. NOW, you can bury the light stakes, check that they are level and then fill the holes with dirt and pack it down.
I’ve always wanted landscape lighting and your post makes it look easy enough that I think I might be able to tackle it.
I just finished installing my Malibu garden lights and three of the lights are not working.
Just happened to come across this article while looking for some other information of landscape lighting and was drawn in by the clever website name (always good to be handy!) but wanted to point out a couple of small changes that can make a HUGE difference in how long your install will continue to work perfectly, or work at all.
Remember to not touch the halogen lights directly with your fingers since grease from your skin may shorten the life span of the bulbs. Use a Direct Burial (DBr) splice connector to connect each landscape lighting fixture to the cable. One wire from each run will go to the common terminal, and one will go to the 12 volt tap terminal.


Make sure you wait for night to fall and fully analyze your customers landscape lighting before leaving. Use 10-gauge wire for the main lines from the transformer to where the lights begin, then switch to 12-gauge wire between the lights. Each halogen light should be receiving 10.5 to 12 volts for a consistent look and to avoid premature burnout. Lay everything out, hook up your lights, test your voltage, and look at your results at night before burying the lines. This is a simple equation, for example, if your lights use 9 watt bulbs, then multiply 9 time the number of light fixtures you have.
Because the lights I bought were on clearance, they were no longer available in the stores.
However, if you accidentally cut your wire, you will have to re-install your lights all over again! The directions that came with the transformer explain that you want your first light to be at or further than 10′ from the transformer. Only to come back 30 minutes later to an error message on the transformer and no working lights. Leave at least 5 feet of slack by the transformer, then loosely run the cable to each fixture according to your layout.. Make sure the lights are correctly positioned, change any bulbs, check for glare from the fixtures and fine tune. Outdoor lighting can be used to illuminate paths, steps and dark zones, plus it can add artfully dramatic emphasis to your yard's best features. Extremely low readings indicate a bad connection somewhere in the system or too many lights on a circuit. You can cheat this by making your wire loop or arc to take up more length on the wire before your first light. Needless to say, she had to dig up every single light and press all the connections tight again. Since low voltage landscape lighting fixtures don't have a polarity, it doesn't matter which fixture gets paired with which cable wire.


If all fixtures on a run aren't within 1.5 volts of each other, adjust your layout or break the run into two. When artfully placed, they can be as beautiful and natural looking as the landscape itself.
Minor voltage adjustments can be made using the voltage controls on the transformer (Photo 2).
The transformer senses darkness and turns on the lights at dusk. I prefer this instead of a timer, especially because it will not need to be reprogrammed as the days vary in length throughout the year.
It’ll save you from re-enacting The Diggingest Dog should your lights fail to work properly! And, because, it is very relaxing sitting outside after dark in the glow of the lights with a drink in hand. The 600-watt transformer shown (about $300) has a built-in timer and photocell, two circuits, and a switch and terminals for setting voltage output to 12, 13 or 14 volts.
This protects the wire from being too taut and will hopefully prevent all your lights from being uprooted should someone accidentally (or intentionally) play soccer with one them.
Be sure to visit our Guide on how to make proper Low-Voltage Landscape Lighting Splices for more detailed information on this topic. If you want to put ten 20-watt lights on a circuit, make a tee connection with five lights on one line and five on the other. The next day she spent too much time on hold with the customer service numbers for the transformer and the light manufacturer. Finally upon removing the last light and plugging in the transformer she found that they suddenly worked.



Plans for front yard book library
Autocad landscape blocks free downloads
Simpson and company landscape
Super bright led landscape lighting


Comments to «How to run low voltage landscape lights»

  1. K_O_R_zabit writes:
    The texture and color you you present by way of your front yard.
  2. YOOOOOUR_LOOOOOVE writes:
    Spend dividends as and will be enjoyed by your household, neighbors and the.