Hampton bay fan 3 speed switch assembly,flush outdoor ceiling fans 60,how to vent an exhaust fan for a bathroom,small base light bulbs in ceiling fans - New On 2016

Even if you are experienced in working with household electricity, the disclaimer at the top of this web page contains important notes about the information in this document, so please read it if you have not already done so. This web page describes repairs made to a ceiling fan with a pull-chain speed control switch. Ceiling fans with pull chains typically include a speed control switch, a direction switch, and a capacitor.
The information in this document is based on my experience fixing a ceiling fan with a 3-speed (plus off) switch and a 5-wire capacitor. In the lower hub of the ceiling fan where the capacitor and switches are located, several wires come down from higher in the fan.
The black wires on the diagram are connected to the black wire that comes down from higher in the fan.
After completing the repair, I noticed than when switching from medium speed to high speed there is sometimes a slight audible "pop" suggesting sparking inside the switch. Before disconnecting any wires, make sure you write down what the original connections are. If you do not know the pattern of the original switch and cannot find any information on it, you might consider disassembling the switch (after removing it from the fan, obviously) to see if you can determine the contact pattern. If you cannot determine the pattern of your original switch or are unsuccessful working from the original pattern, a more in-depth approach is required.
Most likely a capacitor needs to be in series between the incoming power and the motor winding. You also need to know the internal configuration of your capacitor, since ceiling fan capacitors often contain multiple capacitors in one package.
Once you know the internals of your capacitor block, you need to figure out a switch wiring that will create the desired combinations of capacitors.
Note that all this experimentation with wire positions is done on paper, not with the actual wires.
Ceiling fan wiring can be considered as a pretty simple electrical task that an can carry out. Our electrical wiring directory contains diy resources for do it yourself electrical and electrical wiring schematic ceiling fans.
You will need to contact Hunter directly for any wiring schematics they may be able to supply. UStudy aims to provide Educational Content for Polytechnic College students based on the latest K Scheme syllabus of Tamil Nadu. Copyright © 2008 Lakshmi Anand K, Director of MSPVL Polytechnic College, Pavoorchatram.
Quality is never an accident; it is always the result of high intention, sincere efforts, intelligent direction and wise choice of alternatives and skillful execution. So hard-wired controls seem more sensible and more reliable in the long run.A  Ultimately we find these a bit funny-looking -- not the style we prefer -- though they do accommodate our 2-wire installation which is clearly an important plus.Suggestions appreciated! A common problem with these switches is that the pull chain can break off inside the switch.
Unfortunately, there is no agreement among manufacturers about how to configure these components.
However, I have also included some information on how to apply these concepts to the general case, so this information may be helpful even if you have a different type of capacitor or switch. A fan capacitor with more than two wires will probably contain multiple capacitors in one block. Basically this arrangement puts the input power through a capacitor and then into one of the motor windings. The black wire from the fan originally branched into two, but it was necessary to add a third to work with this switch. If you know which contacts the switch connects in each speed position, then you can determine by inspection which wires get connected for each speed setting.


In the case of my fan, as described in the previous paragraph, this means connecting a capacitor in series between the black and gray wires. If you do not know the internal configuration of your capacitor, you could make measurements to discover it. There are quite a number of ways to wire up your ceiling fan, including, you connect the black and red wires from the ceiling fan View this group in the new Google Groups: Group info. I removed all the remote circuit board and want to hook it up to a Need schematic wiring diagram for a 3 speed Hunter ceiling fan. Wiring a ceiling fan is quite easy to do and one need not be a Colors: Ceiling Fan Speed Controller Schematic. Can someone tell me the wiring schematic for a Harbor Breeze ceiling fan remote control unit? Unfortunately, there are many types of fan switches and it is very difficult to find the right replacement. First, increasing the capacitance in series with the coil will typically increase the fan speed.
IMPORTANT: Keep in mind that this wiring is for a particular switch type and a particular fan. Then it is just a matter of finding a way to wire your new switch to replicate those connection patterns.
The speed switch will also be involved of course, since it will determine which capacitor(s) are connected between the black and gray wires. Important: Remember when working with capacitors that they can store a charge even when not connected to anything. However, please know that I cannot provide simple "this color wire goes here" responses to your questions about your particular fan.
However, it may be possible to use a different type of replacement switch with modified wiring. The capacitors come in even more variations, including different numbers of wires, different wire colors, and different capacitance values.
So, even if you are using a different type of fan, please read all the sections because they will help you understand how to figure out your particular ceiling fan. In this regard, note that a short (direct wire, no capacitor) is like an infinite capacitor (for AC power only, not DC). If you cannot get a replacement, or would rather just try to use whatever switch you can find at a local store, the following information may be helpful.
For example, if you know that blue and black connect to make high and orange and black connect to make medium (just for example), then you would try to find a way to wire your new switch to make those same connections when you pull the chain. Next I decided to use the 5 µF capacitor that is accessible through the green wire on the capacitor block.
To check your wiring on paper, carefully trace out what the circuit will be for each switch position.
However, Print this article; Four-way ceiling fans use complex, multiple-speed switches that follow basic wiring schematics. The other gray capacitor wire twists together with the gray wire coming from the direction switch. Discharge the capacitor safely and verify that it is discharged (using a volt meter perhaps) before touching the leads with your hands. To Disassembly a Ceiling Fan Motor, Wiring Ceiling Fans How to Install Ceiling Fans Ceiling Fan Wiring Diagram 1 Ceiling Fan Wiring Diagram 2 Ceiling Fans Wiring – Part 1 Ceiling Fans Wiring Are you having problems with your ceiling fan wiring? Note that the two 5 µF capacitors are in parallel with each other and this combination is in series between the black wire and the motor. The red capacitor wire twists together with the red wire that comes down from higher in the ceiling fan.
Remember that the gray wires from the capacitor are connected internally to the other end of the capacitors that are on the green, brown, and red wires (see capacitor internals diagram above).


Even in a good picture it may be very difficult to read labels engraved or stamped on plastic parts. The approach I took was to measure the capacitance between each possible pair of wires and then draw a diagram. Also, one of the gray wires from the capacitor goes to the gray wire from the direction switch, and from there to the motor. So, for example, it starts by connecting L and 1 on the top deck and, separately, L and 1 on the middle deck. Then verify your design by looking at your diagram and thinking about which wires the switch will connect in each position. What I am describing here is just the logical process I followed for determining what these wires are. So now I have 5 µF in series between black and gray when the switch is in position L-1. After discharging the capacitor, it may be wise to check with a volt meter to make sure no charge remains between any pair of leads. On the next pull it connects 1 and 2, then 2 and 3, then 3 and L, and finally back to L and 1.
The red wire from the fan was connected directly to the red wire on the capacitor, so I left it that way.
I found that the black wire is apparently hot (as usual), and the white is neutral (as usual). If you cannot find the internal configuration of your capacitor, another approach would be to consider obtaining a new capacitor whose internals you do know.
I needed black to connect with this in switch position 1-2, so I added another black on contact 2 on the middle deck. On the top of the direction switch, the yellow is on the right side of the switch and the pink is on the left. At the same time, I wanted black and brown connected on the top deck so that I would have the two capacitors in parallel. YOU MUST TURN OFF THE CIRCUIT THE FAN IS ATTACHED TO AND VERIFY THAT THE FAN IS NOT RECEIVING POWER. In the middle of the direction switch, the white wire comes into the left side and a gray wire is on the right side.
By flipping the order of the yellow and pink wires (by moving the direction switch), the rotation direction of the ceiling fan is reversed. Since white (neutral) is on the left, the gray wire on the right seems to be the wire through which power is supplied to the motor winding. Now when the switch is in position 2-3, the black and gray wires connect on the top deck and there is no connection on the bottom deck.
Note that I had to put the gray wire in contact 3 on top because even though the middle deck has black on 2 as well, it also has black on L, which would make position 3-L another high, rather than off. In my fan, it originally connected directly to the capacitor and not the speed switch, so I left this connection as it was.
This is just an example of the logical approach required to develop a suitable switch wiring once you know the pattern of your switch and the internals of your capacitor. The above information about wire colors is not intended to apply directly to any particular fan.



Ceiling fan direction diagram questions
Bvb fanshop cap
Fansided college football game
Hunter fan universal remote codes
18.10.2014 admin



Comments to «Hampton bay fan 3 speed switch assembly»

  1. gizli_baxislar writes:
    Into the canopy and is not blocked from getting breeze it creates, and just the ambiance.
  2. AKROBAT writes:
    Say that ceiling fans effectively placed.
  3. DoDaqDan_QelBe writes:
    Appraisal Of Your Property You are going.